Replacement Bearing and Race For Lippert Turning Point Pin Box

Question

Question:

Looking for a rebuild kit for a lippert turning point 16k fifth wheel hitch. Mainly in need of the inner nylon sleeve and the bearing. It’s off a 2021 grand design. Thanks

asked by: Jacob K

0

Expert Reply:

We do have the Bearing # 25580 and Race # 25520 needed for your 16k Lippert Turning Point 5th wheel pin box. Unfortunately, according to Lippert if the inner nylon sleeve is damaged and needs replaced the entire pin box must be changed. And the Turning Point uses an exclusive bolt pattern so that it can only be replaced with another Turning Point.

expert reply by: Bud M

0

Answer 1

I recommend using the 5th Airborne Custom Wedge for Husky / Valley Fifth Wheels #SWW-04 for your application as we've found it to fit really well with the Turning Point pin boxes. Attached is a review video as well as a clip of a customer review…

view full answer...

Answer 2

The Curt Turning Point should come with a universal wedge, which often times is sufficient. There are times when the universal wedge isn't quite good enough and you will need a custom wedge. If you switch trucks/hitches often, then a universal…

view full answer...

Answer 3

The Replacement Wedge Block for Lippert Turning Point Pin Box #LC79UD is a universal wedge that has been confirmed to fit both the Lippert Turning Point pin boxes and B&W fifth wheel hitches. If you bought a trailer secondhand and didn't have…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Bearing and Race For Lippert Turning Point Pin Box

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching