Comparing Dexter Trailer Hub and Drum Assembly 8-219-4UC3-EZ and 8-219-4UC3

Question

Question:

What is the difference between these two hubs?

asked by: Gregory S

0

Expert Reply:

The Dexter Trailer Hub and Drum Assembly # 8-219-4UC3 fits a standard #42 Spindle # TRU57FR. While the Dexter Trailer Hub and Drum Assembly # 8-219-4UC3-EZ fits a E-Z Lube #42 Spindle # TRU37FR. You will need to select the appropriate assembly based on your spindle.

expert reply by: Bud M

0

Answer 1

Hey Jesse. The Terran Axle Trailer Idler Hub Assembly for 5,200 to 6,000 lbs Axle - 6 on 5-1/2 item #TX43VJ is indeed compatible with the #42 Spindle for 5,200-lb to 7,000-lb Trailer Axles - 2-1/4" Diameter item #TRU57FR. Both of these parts are…

view full answer...

Answer 2

To verify if your hubs on your 6,000lb Dexter axles are going to fit the etrailer AxleTek 7,000LB Axle #e35GR you will need to verify what bearings and grease seals are used on your hubs. The new axles will use a #42 Spindle #TRU57FR, and this is the…

view full answer...

Answer 3

As long as your spindles are 4.75 inches from seal to threading like #TRU24FR or #TRU57FR they are compatible. I've attached a photo to assist. You will be able to use the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Comparing Dexter Trailer Hub and Drum Assembly 8-219-4UC3-EZ and 8-219-4UC3

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching