Wiring Harness that Does Not Require Splicing for a 2021 Ford EcoSport

Question

Question:

I have a 2021 ecosport. I found the correct number for the hitch. I was wondering if that have a wiring harness for that vehicle and if so what number it was. Thanks

asked by: Rick B

0

Expert Reply:

I would be happy to help you. I'll start out by confirming that the Curt Trailer Hitch Receiver item # C12188 you were looking at is a confirmed fit for your 2021 Ford EcoSport. I have linked an installation video so you can follow along and see the final product.

For a wiring harness you will want the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit item # 119250KIT. This harness does not require any cutting or splicing of wires. It has ZCI sensors that can read the signals sent through your EcoSport's wires just by clamping onto them. This wiring harness will provide you with a 4-flat connector.

expert reply by: Jerred H

0

Answer 1

To get your 2021 Ford EcoSport set up to tow a small trailer, I recommend starting with the Curt #C12188. This is a very quick and easy install and shouldn't take more than about 30 minutes to complete. This is an American made hitch that will…

view full answer...

Answer 2

Hey Harry, thanks for reaching out! The Curt Trailer Hitch Receiver #C12188 is a custom fit installation for your 2018 Ford EcoSport and has holes in the mounting brackets that match up to the holes in your vehicle frame for a no-drill installation.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...