What are the Wiring Functions for Pedestal Mount Trailer Stop, Turn and Tail Light

Question

Question:

I recently bought this light? question is which is the ground? red or black ?thanks foe thw AWESOME FAST DELIVERY

asked by: JOE R

0

Expert Reply:

The answer is neither! This particular light, # ST51RB, grounds through the mounting location so it will need to be attached to a clean and corrosion free bare metal surface. The red wire is for tail lights. The black wire is for brake and turn signals.

expert reply by: Michael H

0

Answer 1

On the Optronics Pedestal Mount 3-Function Tail Light, part #ST51RB, the red wire would be for the tail light signal and the black wire is for brake and turn signal. The light gets grounded through the mounting pedestal to the trailer frame so it…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 8

That is a Timken seal with the part number 171255TC, so you can use the Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 1 #58846 as the replacement or you can get a pair with part #RG06-050.

view full answer...

Answer 9

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer in…

view full answer...

Answer 10

The particular parts you need to install a fully-functioning 7-Way on your 2019 Toyota Highlander Hybrid will depend on what exactly it's already equipped with. Either way you will need to start by adding a 4-Way connector harness. If your…

view full answer...

Answer 11

Hey Roger, The oxidation of the plastic causes this and unfortunately isn't something that you can really get a rating on from the manufacturer. It's the same as the plastic seats at an outdoor stadium. Keeping the trailer clean and out of…

view full answer...

Answer 12

The brake assemblies you have are Dexter assemblies that are 12 inch by 2 inch in size. There should be a number after the FF that will tell you what size brakes they are. If you can't identify any numbers you will want to replace them with the…

view full answer...

What are the Wiring Functions for Pedestal Mount Trailer Stop, Turn and Tail Light

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching