Could Brophy Ball Mount # BR39FR be Used in Class I Trailer Hitch

Question

Question:

I didnt see mention of whether this would work with a Class I or II hitch. Will this work with a Class I hitch?

asked by: Nate

0

Expert Reply:

The Brophy Drawbar part # BR39FR could be used in a Class I hitch but typically Class I hitches require a specific ball mount be used so I'd check with the manufacturer of your trailer hitch.

expert reply by: Jameson C

0

Answer 1

I may have another option but unfortunately there are no Timbren or Firestone suspension enhancement options confirmed to fit your 2013 Nissan Juke SV. The only option is to measure the spacing between the coils of your coil springs as depending on…

view full answer...

Answer 2

I have a solution for you to be able to get to 7" of total rise. The Brophy Anti-Rattle Drawbar #BR39FR is a 1-1/4" ball mount that will give you 5-1/2" inches of rise. That is the largest rise that I have been able to find. You can…

view full answer...

Answer 3

The 1-1/4 inch ball mount with the largest rise we offer is part #BR39FR from CR Brophy which offers a 5-1/2 inch rise. The rise of the ball mount doesn't need to be exactly equal to the height difference between the receiver and the trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

Hey Larry that's quite a bit of rise! They don't make those for 1-1/4" hitches but I can get you closeish. You'll want to start with the Curt Class I Drawbar item #C45024. It has a 5" rise from the top of the inside of the hitch…

view full answer...

Answer 8

The 1-1/4" receiver does limit you but I have a solution to achieve a 7" rise for a ball mount. You do not want to use an extension since it will cut your capacity in half which means you wouldn't be able to tow that trailer. What you…

view full answer...

Answer 9

I do have a great option for you, however the EcoHitch Hidden Trailer Hitch #306-X7317 that you referenced is not confirmed to fit the GT model of your 2018 VW Passat. We have reached out to Curt though in the past and were able to verify that their…

view full answer...

Answer 10

To wire two 6-volt batteries in series to produce 12-volts, you would connect the load to the positive terminal of battery #1. Connect the negative terminal of battery #1 to the positive terminal of battery #2. Ground the negative terminal of battery…

view full answer...

Answer 11

I do have a trailer hitch receiver that will fit your 2004 Volvo XC70 but it has a 1-1/4" receiver tube opening, not a 2" receiver tube opening. They do not make one with such for your Volvo and the Curt Trailer Hitch Receiver part #13559…

view full answer...

Answer 12

After speaking to my contact at Curt, I found the most height extension you can achieve with the Curt Class II Euro Style Drawbar #C45592 for your 2011 Volkswagen Golf is with the Curt Class II Drawbar #C45015. This is a 5-1/8 inch rise drawbar which…

view full answer...

Could Brophy Ball Mount # BR39FR be Used in Class I Trailer Hitch

Product Page this Question was Asked From

Continue Researching