What Is The Cardboard Piece Inside My RV Microwave

Question

Question:

I was setting up my new microwave/conv Furrion RV Microwaves - FMCM15SS and inside there is a square about 3x3 inch pieces of cardboard that is covering a opening. should that be taken off of the right inside wall of the microwave?

asked by: James M

0

Expert Reply:

The cardboard piece you're referring to in your Furrion Over the Range RV Convection Microwave # FMCM15SS covers the waveguide system that feeds microwave energy into the cavity of the microwave and should not be removed.

expert reply by: Kevin C

0

Answer 1

I spoke with Furrion about the Furrion Microwave FMSMA15-SS and they informed me that the Furrion Over the Range RV Convection Microwave part #FMCM15SS is the correct replacement. I verified all of the dimensions and power ratings for you as well to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hey Dale, both DeeMax and Hydrastar make really nice disc brake components. Either kit is going to work really well for your 2022 Grand Design Reflection 337RLS. If you want the best of the best and don't mind paying for the premium brand then go…

view full answer...

Answer 12

Hey Dale, you can install Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers #RM-2460 with a SumoSprings kit like the part #SS26MV. The SumoSpring would just engage a little earlier since it installs on top of the u-bolt plate which…

view full answer...

What Is The Cardboard Piece Inside My RV Microwave

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching