Replacement D-Spud for Phoenix Faucets RV Tub and Shower Diverter Faucets

Question

Question:

I only need the shower diverter piece to fix my existing faucet, can you help me with that?

asked by: Rebecca

0

Expert Reply:

We have the Replacement D-Spud for Phoenix Faucets RV Tub and Shower Diverter Faucets, # PF183007 that matches as a replacement part for your Phoenix Faucets, # PF213332.

expert reply by: Michael R

0

Answer 1

Hi Ken, The rooftop unit is just a condenser, which is kind of the same setup as a residential system. It just turns on when the controller tells it to which is why it's the only part you can really swap out without having to completely replace…

view full answer...

Answer 2

I went and pulled a Replacement D-Spud for Bathroom Sink Diverter Faucets #PF273001 and determined that it has 7/16 inch fine threads.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 11

Hey Dave, the install harness part #3063-P does fit to the green connector that is under your seat in your 2025 Mercedes Benz Sprinter 4500 and would work great with the P3 part #90195 which is widely considered to be the best controller around. I…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement D-Spud for Phoenix Faucets RV Tub and Shower Diverter Faucets

Product Page this Question was Asked From

Continue Researching