Troubleshooting Trailer Hubs that Leak Grease After Seal Replacement

Question

Question:

Im having issues with these seals leaking grease past the spindle onto the brakes. Seal size in 1.719 x 2.565 for 3500lb boat trailer. I always pump grease by hand and rotate the tire to spread evenly. It doesnt leak right away, maybe after a couple of road trips. Do you have any thicker ID seals that will seal on the spindle better? Ive tried other brands and same thing.

asked by: Ben

0

Expert Reply:

What's happening is that you are actually overfilling your hubs which grease and that is why the seal is leaking. This is very easy to do with EZ lube spindles and Bearing Buddies which is why we generally recommend just packing the hubs by hand and not adding additional grease into the zerk fitting.

I attached a video that covers packing bearings for you to check out as well.

expert reply by: Jameson C

0

Answer 1

While we do not carry the exact same wheel studs as the one's you're looking for, however I'd be happy to help you measure your wheel studs to see if we have a comparable replacement. What you're going to want to do is, measure the…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Troubleshooting Trailer Hubs that Leak Grease After Seal Replacement

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching