Replacement Switch For A KEDU HW60D E195428 Rocker Switch

Question

Question:

Need to replace ram 3500 switch KEDU HW60D E195428 WITHN JUMPER WIRES

asked by: Robert R

0

Expert Reply:

I looked up the Kedu HW60D E195428 switch you're referencing, and It appears to be a standard rocker switch. That being said, you can use the Mini Momentary Switch # 37213445, which has a cutout dimension of 0.745 inch tall x 0.5 inch wide.

expert reply by: Bryce D

0

Holly

9/17/2024

We need a 4 prong - NOT a 6 prong switch

Bryce D.

9/18/2024

@Holly Holly, check out the Single Slide-Out Momentary Switch # 37212395 then. This is also an On/Off/On switch that has 4 prongs instead of 6, and will fit into slide outs measuring 1.85" tall x 1.20" wide.

Answer 1

The outer diameter of the tire size you have of 205/75R14 is 26.3 inches so a cover like the #290-3954 would be your best option.

view full answer...

Answer 2

To determine the necessary replacement bearings, you'll need to pull one of your hubs and obtain the reference numbers off your existing bearings, both inner and outer. You'll also need the diameter of the hub bore where the grease seal sits…

view full answer...

Answer 3

Thank you for the picture of your Kedu HY60D switch, the Single Momentary Reversing Switch #37213865 has the same 4 prong connection on the back as your pictures. The cutout dimensions for this switch are 0.835" tall x 1.457" wide.

view full answer...

Answer 4

When using a weight distribution system you will have nearly the same turning ability as you would without a weight distribution system in most cases. The difference is only slight when using a system like the Equal-i-zer #EQ37120ET where other…

view full answer...

Answer 5

If you're referring to the internal 10 amp fuse in the top of the High Pointe Over the Range RV Convection Microwave #HP94ZR there have been owners who found that the door latch has two switches that wear over time and and end up causing the fuse…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Switch For A KEDU HW60D E195428 Rocker Switch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching