Tight Turning Ability with Weight Distribution System Installed

Question

Question:

With a typical value priced weight distributing hitch with spring bars installed can I make tight turns, such as a u turn on the road or parking lot maneuvers requiring tight turning going forward. How about backing up, tight turns ?

asked by: Tom

1

Helpful Expert Reply:

When using a weight distribution system you will have nearly the same turning ability as you would without a weight distribution system in most cases. The difference is only slight when using a system like the Equal-i-zer # EQ37120ET where other systems may have further restrictions. This system will have just a slightly wider base but you can still make U-turns as needed.

Some systems do not allow backing, but those systems are only the ones with the friction bar and it is due to the adjustability of that bar as well as the location. The Equal-i-zer # EQ37120ET will be able to back up without issue. I've attached an article to further assist with common questions.

You will want to use a thin walled socket like # ALL643216 to install the included hitch ball on this system.

expert reply by: Jason S

1

Answer 1

Some weight distribution system prohibit reversing because doing so could damage the system. If you are backing up in a straight line though it would be fine. But to make turns while backing up you would need to disengage the spring bars and/or the…

view full answer...

Answer 2

Thanks for providing all of the information for your axle. This axle is going to use the standard 3,500 lb axle bearing sizing. You can use the Bearing Kit #BK2-100, which will come with bearings, races, seals, cotter pin and tang washer - everything…

view full answer...

Answer 3

There are a few differences between a chain or bar weight distribution hitch. A chain weight distribution hitch like the Reese Weight Distribution System #RP66021 will not have sway control built into the system. It would require you to add either…

view full answer...

Answer 4

I looked up the Kedu HW60D E195428 switch you're referencing, and It appears to be a standard rocker switch. That being said, you can use the Mini Momentary Switch #37213445, which has a cutout dimension of 0.745 inch tall x 0.5 inch wide.

view full answer...

Answer 5

Hi Kendrick; according to Air Lift the LoadLifter 5000 Air Helper Springs #AL95QF do not fit the TRD Pro models. However, we have had at least two customers successfully install them on the 2023 and 2024. One came back and complained about the impact…

view full answer...

Answer 6

Hey Michael! When you're choosing a weight distribution hitch the most important factor is the tongue weight of the trailer. It looks like the dry/unloaded tongue weight of a Brinkley Z Air 297 is 924 lbs. Once you add batteries and propane you…

view full answer...

Answer 7

Hey there Layla! There are a few different forms of weight distribution hitches, but the majority of the systems that have sway control use friction bars, which work similar to brake pads on your vehicle. This works really well, but it can sometimes…

view full answer...

Answer 8

Hello John, thanks for reaching out. We do carry parts for the Equalizer weight distribution hitches, and we actually have exactly the part you are looking for. What you will need is the Inner Link Plate #EQ90-02-5210 and outer link plate…

view full answer...

Answer 9

Between the two kits you mentioned the Equal-i-zer part #EQ37120ET is the best choice. This is the highest quality option out there for a weight distribution system and is what Curt tried to emulate with their TruTrack part #C17501. The Curt kit is…

view full answer...

Answer 10

Weight distribution/sway control (WD/SC) systems need to be tuned to your trailer tongue weight in order to work properly. A system rated too low for your actual tongue weight (TW) will not have the stiffness needed to shift trailer TW forward to the…

view full answer...

Answer 11

That's what we're here for Jim you're not bothering anybody. I found those parts you need for your Equal-i-zer Weight Distribution System item #EQ90-00-1000 and have listed them below: Replacement Snap-Up Lever for Equal-i-zer Weight…

view full answer...

Answer 12

The most accurate method to determine your tongue weight is to use a commercial scale at either a truck stop or quarry for example. The linked article details how to do this. You may have to pay a small fee for this service but it will provide a more…

view full answer...

Tight Turning Ability with Weight Distribution System Installed

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching