Is Trimming Required to Install the etrailer Hitch # e56RR?

Question

Question:

is there trimming required for the installation of the e56RR?

asked by: Pedro

0

Expert Reply:

Yes, there is trimming required for the installation of the etrailer Hitch Receiver # e56RR. The trimming involves part of the underside fascia panel. I went ahead and attached a photo of the trimming area and dimensions.

expert reply by: Bob C

0

Fascia Trimming Dimensions of the etrailer Hitch # e56RR
(click to enlarge)

Answer 1

As far as the Curt hitch #C22UR and the Draw-Tite #DT55MR, we unfortunately haven't had a chance to install the hitches yet. With that being said, we do not have the precise ground measurements when fitted onto a 2021 Toyota Sienna. However, both…

view full answer...

Answer 2

I recommend our etrailer Trailer Hitch Receiver #e56RR for your 2024 Toyota Sienna hybrid. I prefer this receiver as it has a matte black finish which gives it a clean factory appearance. I also find this finish to be more durable than the gloss…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Good morning to you as well Steve, and congrats on your new van! I would be more than happy to make a recommendation for you! The best hitch for your 2026 Toyota Sienna, is going to be our etrailer item #e56RR. This is a class III hitch with a…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Ben! The Curt does have that restriction on the vertical bike racks so I recommend the TowSmart Trailer Hitch #TS82VR. This has a higher tongue weight capacity and will allow you to carry the VelociRAX. It would be a good idea to add the etrailer…

view full answer...

Is Trimming Required to Install the etrailer Hitch # e56RR?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching