Replacement Axle Bolt and Nut Kit for Yakima Rack and Roll Trailer

Question

Question:

Hello. I have a Yakima Rack and Roll and need to replace an axle bolt and nut. Do you carry this replacement part? Thanks!

asked by: Doug B

0

Expert Reply:

We do have replacement axle bolt and nut kits for the Rack and Roll trailers like # Y08107 with the part # Y8880180.

expert reply by: Jameson C

0

Answer 1

Hello Dan, those a definitely some uncommon bearing sizes. It sounds like this trailer is pretty old and uses bearing sizes that are basically obsolete. We do have the Timken #TMK83VR bearing that has a 3/4" ID. This bearing is generally used on…

view full answer...

Answer 2

You'd only need to adjust the Heavy Duty Shocks for Yakima Rack and Roll Trailer #Y08110 if you're hauling a heavy load that is causing your shocks to bottom out. These shocks have 4" vertical adjustability to combat that, so you'd…

view full answer...

Answer 3

The Replacement 4" LED Tail Light for Yakima Rack and Roll Trailer item #8880212 is the correct tail light for the Yakima Rack and Roll Trailer item #Y08106 or item #Y08107. It will not replace your brake light. I just spoke with my rep at…

view full answer...

Answer 4

The Spare Tire with 5 Spoke Rim for Yakima Rack and Roll Trailer #Y08121 has wheel dimensions of 16" diameter x 1.85" wide and tire dimensions of 16" diameter x 3.25" wide. This is the tire #Y8880282 you referenced with inner tube…

view full answer...

Answer 5

Hey Richard, the Yakima Rack and Roll trailer part #Y08106 does not come with axle grease but you could use some LMX red grease like the part #L11380 or even any bearing grease you have on hand.

view full answer...

Answer 6

I contacted the manufacturer about replacing the 3.25"-16" tires on your Yakima Rack and Roll Trailer with 3.50"-16" tires. They recommend that you continue to use the Replacement Tire for Wheel on Yakima Rack and Roll Trailers…

view full answer...

Answer 7

The Replacement Axle Bolt Kit for Yakima Rack and Roll Trailers #Y8880180 measures 9" long total and measures 7-7/16" from the bottom of the bolt head to top of the threads. It is also 14mm (0.55") in diameter. I have attached a…

view full answer...

Answer 8

Hey Michael, The wheel for your Yakima Rack And Roll Kayak Trailer #Y08106 would be held in place with a single bolt. The bolt head would stick out past the wheel so you should be able to use another wrench to hold the bolt while you torque down the…

view full answer...

Answer 9

I went out to the warehouse and pulled Replacement Axle Bolt Kit #Y8880180 to measure the cotter pin in the kit. The pin is approximately 0.11 inches thick whereas the hole is just slightly larger than 0.125 inches (1/8). The pin has an overall…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Axle Bolt and Nut Kit for Yakima Rack and Roll Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching