Replacing The Wheel On A Yakima Rack And Roll Kayak Trailer # Y08106
Updated 06/20/2024 | Published 06/14/2024 >
Question:
I have a replacement for a Yakima rack and roll wheel. After replacing a flat tire on the trailer and attempting to torque the wheel to the recommended 57 lbs pretty stout, I realized the pin would not at that torque level. Since the nut rotates around the bolt or the bolt rotates inside the nut, it needs to be aligned perfectly to inset the cotter pin. Any guidance on how to accomplish that would be appreciated. Thank you!
asked by: Michael M
Expert Reply:
Hey Michael,
The wheel for your Yakima Rack And Roll Kayak Trailer # Y08106 would be held in place with a single bolt. The bolt head would stick out past the wheel so you should be able to use another wrench to hold the bolt while you torque down the nut. I've attached a video below where Joe does this starting at the 3:40 minute mark.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Yakima Rack and Roll Trailer - 78"
- Shop: Replacement Tire for Wheel on Yakima Rack and Roll Trailers - Qty 1
- Search Results: yakima rack and roll
- Shop: Replacement Wheels for Yakima Rack and Roll Trailer - Qty 2
- Video: Yakima Rack and Roll Trailer Assembly
- Shop: Spare Tire with 5 Spoke Rim for Yakima Rack and Roll Trailer
- Shop: Replacement Inner Tube for Wheel on Yakima Rack and Roll Trailers - Qty 1
- Search Results: 7 pin to 4 pin adapter
- Search Results: yakima jaylow
- Search Results: yakima tire
- Video: Breaking Down the Spare Tire with 5 Spoke Rim for Yakima Rack and Roll Trailer
- Video: Checking Out the Replacement Tire for Wheel on Yakima Rack and Roll Trailers
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Yakima Kayak Trailer for 5 Kayaks - 250 lbs
- Search Results: yakima roof bike racks
- Video: All You Need to Know About the Replacement Wheels for Yakima Rack and Roll Trailer
- Search Results: trailer tires and wheels
- Search Results: yakima kayak trailer
- Video: Ultimate Overview of the Replacement Inner Tube for Wheel on Yakima Rack and Roll Trailers
- Shop: Trailer Wiring
- Q&A: Replacement Wheels and Tires For Yakima Rack and Roll Trailer
- Q&A: How Can I Carry Two Kayaks on the SportRack Roof Rack on 2008 Subaru Legacy
- Q&A: Yakima Rack and Roll Trailer 66 Inches Disassembly for Storage
- Q&A: Can Wheels on Yakima Rack and Roll Trailer Be Folded Flat
- Q&A: Can You Use a 3.50"-16" Tire on a Yakima Rack and Roll Trailer Instead of a 3.25"-16"Tire
- Q&A: Bottle Jack Recommendation for Supporting Yakima Rack and Roll Trailer to Change Spare
- Q&A: Yakima Rack and Roll Trailer Assembly Video
- Video: Hands-On with the Replacement Left Side Wheel Block for Yakima Rack and Roll Trailer
- Video: Mount: Yakima HighRoad Roof Bike Rack on a 2017 Toyota RAV4
- Shop: Roof Rack

Michael M.
6/20/2024
Yes, I've had the trailer for quite a while now, and I'm familiar with changing the tire. My question is specific to getting the correct recommended torque on the wheel. The recorded torque is 57 lb. When turning the nut, it invariably falls on 57 when the nut is not lined up with the hole in the bolt. Should I over or under-torque?