How To Wire Replacement Light Switch and Replacement Power Switch for RAM 3,500 Lb Jack

Question

Question:

Is there a wiring diagram for the switches that go in this Jack?

asked by: Tony G

0

Expert Reply:

In regards to the Replacement Light Switch part # EJ-3520-LSW and Replacement Power Switch part # EJ-3520-PSW, you can reference the attached photo for help with installation but we don't have any wiring diagrams at this time.

expert reply by: Conner L

0

How To Wire Replacement Light Switch and Replacement Power Switch for RAM 3,500 Lb Jack
(click to enlarge)

Answer 1

Your RAM 3550 Jack will use both the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW and the Replacement Light Switch for Electric Trailer Jack with Footplate #EJ-3520-LSW.

view full answer...

Answer 2

What you need to replace the light in your Ram Jack a-frame powered jack is the part #EJ-3520-LT.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

How To Wire Replacement Light Switch and Replacement Power Switch for RAM 3,500 Lb Jack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching