Where is the Port for the Block Heater # KH11815 on a 2018 Ford F-150 with a 3.5L V6 EcoBoost Engine

Question

Question:

I am interested i buying the cartridge type block heater for my 2018 ford F150 3.5L ecoboost with 10 speed transmission and super crew cab. My question is, where is the port located for the cartridge to fit in? I would like to do the installation myself so I am curious how involved the job will be. The videos make it look easy and I have worked on a lot of cars. Thanks for the info,

asked by: John C

0

Expert Reply:

I confirmed with Kat's Heaters that the port location for the Custom Fit Engine Block Heater # KH11815 on your 2018 Ford F-150 with the 3.5L V6 EcoBoost engine is on the right front of the block. I went ahead and attached a diagram that shows this location on your conventional engine.

expert reply by: Bob C

0

Port Location for # KH11815 on a 2018 Ford F-150 with a 3.5L V6 EcoBoost
(click to enlarge)

Answer 1

The Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11815 is a fit for the 3.5 EcoBoost you have. It will fit in the right front location of your engine. You will simply clean the cartridge hole with…

view full answer...

Answer 2

Hey George, according to Kat's Heaters, their #KH11815 cartridge style engine block heater installs into the core hole on the right side of the engine block toward the front of the motor on your 2013 Ford F-150 with the 3.5 liter ecoboost engine.…

view full answer...

Answer 3

According to Kat's Heaters, their #KH11815 cartridge style engine block heater installs into the core hole on the right side of the engine block toward the front of the motor on your 2013 Ford F-150 with the 3.5 liter ecoboost engine. .

view full answer...

Answer 4

The correct Kat's Heater Engine Block Heater that fits the 3.5L Engine in your 2016 Ford F-150 is the part #KH11815. According to Kat's Heater this installs on the Right Front location of your engine block (see attached picture). I confirmed…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Where is the Port for the Block Heater # KH11815 on a 2018 Ford F-150 with a 3.5L V6 EcoBoost Engine

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching