Brake Controller For A 2022 Chevrolet Traverse

Question

Question:

I buying a 2022Traverse with the factory tow package. Im going get either the Curt C51180 which I believe SHOULD just plug into my 7 pole connector or the CurtC 27JR. Question. Is there a custom harness the goes from the Traverse to the C27JR or must I use the universal. Thanks Bill

asked by: Bill H

0

Expert Reply:

There is not a vehicle specific adapter for your 2022 Chevrolet Traverse, so you will need to use the universal harness # C27JR.

In order to complete installation of the Curt Echo Wireless # C51180, you'll need to add a 7 way # ETBC7L, if you do not have one present already.

expert reply by: Bryce D

0

Answer 1

I highly recommend the Redarc Tow-Pro Liberty Brake Controller Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers #RED24FR. It is a permanent install and will be all hidden, save for they small control knob. You will need a…

view full answer...

Answer 2

We can help get the Tekonsha Prodigy P2 Trailer Brake Controller, #90885 connected to your 2022 Chevrolet Traverse. But there is not a simple plug-in wiring adapter such as the #3026-P available. From our Tech Support contact at Tekonsha they…

view full answer...

Answer 3

For your 2022 Chevy Traverse I recommend the Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional #90195. This proportional brake controller is our most popular selling model and is transferable between automobiles. It…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...