Should Grease be Used to Fill Space Inside After Hub Installation
Updated 12/27/2021 | Published 12/24/2021
Products Featured in This Question
Question:
I ordered the pre-greased hub and installed it. It is great but i noticed there is more space inside Do I need to add more grease to fill it up? These is some play when is hub is installed. After putting on the cap, should I fill it completely up?
asked by: Patrick C
Expert Reply:
When installing your Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased # AKIHUB-440-2-EZ-1K there should not be any "play" or space. Since it is pre-greased, more grease is not needed. I recommend checking your spindle to make sure this hub is correct. It uses a # L44643 inner and outer bearing, so your spindle should measure 1" where both bearings ride.
I have attached a helpful article on replacing/packing bearings, as well as a video showing the process and what your hub should look like when it is on the spindle.
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- 14 Inch Wheel
- 8 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: 010~036~00
- Search Results: 370014
- Search Results: 9~28~1
- Shop: Timken 412920 Grease and Oil Seal - I.D. 2.250" / O.D. 3.376" for 5.2K, 6K, and 7K Axles
- Shop: Dexter Trailer Brake Drum for 12,000-lb and 15,000-lb Axles - 12-1/4" x 5" - 8 on 6-1/2
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 12-1/4" - Left/Right Hand Assemblies - 15K
- Shop: Unitized Oil Seal - I.D. 2.750" / O.D. 3.779" for AL-KO/Hayes K80 and 10K GD Axles - Qty 1
- Shop: Kodiak Disc Brakes - 13" Hub/Rotor - 8 on 6-1/2 - Dacromet - 7,000 lbs - E-Z Lube
- Shop: Dexter Electric Trailer Brake Assembly - Self-Adjusting - 12-1/4" - Right Hand - 9K to 10K
- Shop: Unitized Oil Seal - I.D. 3.125" / O.D. 4.500" for 10K to 16K Heavy Duty Axles - Qty 1
- Search Results: timbren vehicle suspension
- Search Results: spare tire mount
- Shop: Suspension Enhancement
- Q&A: Recommended Spare Tire Carrier That is Not Angled Upwards
- Shop: Brake Controller
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Q&A: Why is 25' Wishbone 4-Way Trailer Wiring Harness Also Referred to as 21' - 30' Long
- Q&A: Recommended Towing Set Up for a 2012 Toyota RAV
- Video: 2012 Chevrolet Express Van Tekonsha Prodigy P2 Trailer Brake Controller: Complete Installation
- Search Results: 40 amp circuit breaker
- Search Results: tires
- Q&A: Should a Trailer Hub Be Completely Filled With Grease After Being Installed On Spindle?
- Q&A: How Full Should Boat Trailer Hubs be Filled with Grease
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Hubs and Drums
