Is There a Hand Rail Available for MORryde Flip Tread Steps

Question

Question:

Is there a handrail available for the Morryde Flip Tread RV entry step. If not do the body mount fit into the brackets of the existing folding rail?

asked by: Bill

0

Expert Reply:

MORryde does not offer a hand rail for the Flip Tread Steps like the part # MR42UR so you'd need to use a folding hand rail that attaches to the RV like with the Lend-A-Hand part # AM-533.

expert reply by: Jameson C

0

Answer 1

Hey Tim, thanks for the photo! The Lend-a-Hand Extra Large Folding Grab Handle #AM-533 probably doesn't have the exact same bolt hole placements as your current Camco Short Folding Handle, so you may have to repair some holes to ensure you…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

view full answer...

Answer 4

The steps are approximately 19.415" in width for the MORryde Flip Tread RV Steps #MR42UR. To get wider steps you would need to size up in mounting width to something like the #MR28RR, but would need to have enough room for the steps to properly…

view full answer...

Answer 5

The Handrail for Second Generation 4-Step MORryde Steps #MR73AR is designed to be used with the StepAbove steps. Unfortunately this rail will not work for your MORryde Flip Tread RV Steps #MR42UR. That being said, the best solution is to add a…

view full answer...

Answer 6

The hinge plate of the MORryde Flip Tread RV Steps item #MR42UR is 4-1/4" in depth so you have some room to work with. According to MORryde, you will need 5-1/2" of clearance inside the door threshold to fold up the steps. I attached a…

view full answer...

Answer 7

I attached a link to the install instructions for the MORryde Flip Tread RV Steps #MR42UR to this page for you to check out as well.

view full answer...

Answer 8

Welcome back Mike! To attach a set of steps to your Palomino 1251 truck camper, I recommend the TorkLift GlowStep Camper Scissor Steps item #TLA7804. They're going to bolt directly to your Palomino right below the door, with the included…

view full answer...

Answer 9

I spoke with MORryde and they stated the item number you were given does not match anything they have. Possibly it's the item number that the RV shop uses instead of the manufacturer number? Based on your photos it appears to me that you have a…

view full answer...

Answer 10

Our part number for the MORryde Step Above part #STP-212 is the part #MR88RR. If you wanted the strut assisted version you'd want the part #MR85RR instead. The strut assisted version is not quite as detachable as the strut assisted.

view full answer...

Answer 11

Hello Theresa, Yes, the TorkLift GlowStep Revolution #TLA8002 will work on your 2022 Forest River Aurora 18BHS based on the measurements you provided. Your 24 inch ground clearance is right within the operating range for the 2-step #TLA8002, and the…

view full answer...

Answer 12

Hey John! You weren't finding that SolidStep because Lippert discontinued it in 2024 and that table wasn't updated to reflect this. What I recommend instead is the MORryde StepAbove RV Steps #MR26RR. These are designed to fit 23-3/4" to…

view full answer...

Is There a Hand Rail Available for MORryde Flip Tread Steps

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching