Installation Instructions for MORryde Flip Tread RV Steps

Question

Question:

Where would I find the instructions for mounting the stairs? There were no manual, warranty or installation information in the box. Thanks for your help.

asked by: Phil S

0

Expert Reply:

I attached a link to the install instructions for the MORryde Flip Tread RV Steps # MR42UR to this page for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Do you need the instructions for the 5th wheel hitch, installation kit, or both? I have linked instructions for the Reese 16K fixed version and the square tube slider base for you. For the install kit I would need to know which kit you have. I have…

view full answer...

Answer 2

My research on the Forest River website shows that their Rockwood Series of 5th wheel trailers currently comes equipped with a Reese Revolution hitch. The gross weights (GVWR) of the various Rockwood-series trailers varies considerably across models…

view full answer...

Answer 3

The Curt A16 #C16521 is going to give you the highest available hitch setting, though it still is not going to give you a 7 inch clearance over the top of your 2017 Ford F-250's bed. If you need additional clearance to stay level, you would want…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, the puck system used on the 2016-2019 Chevy/GMC trucks is different than the pucks used on the 2020 and newer trucks. So you would need a 5th wheel like the B&W Companion #BWRVK3710 for your 2020 GMC Sierra 3500 with an 8' Bed. If you…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

Hey Mike, thanks for reaching out! The 16K Pullrite SuperGlide #PUL43RR is an excellent option for towing your Grand Design with your 2025 F-250, and if you lockout your Lippert Turning Point pin box you'll be able to use them together. You…

view full answer...

Installation Instructions for MORryde Flip Tread RV Steps

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching