Is There Fascia Trimming Required to Install the Curt Hitch # C11427 on a 2011 Toyota Avalon

Question

Question:

Does installation of this hitch require trimming of the fasia trim around exhaust

asked by: Eric

0

Expert Reply:

To install the Curt Trailer Hitch # C11427 that you referenced, there will be some fascia trimming required. around the exhaust or anywhere for that matter.

This install does not require any drilling and only requires temporary lowering of the exhaust. Check out the installation instructions I attached also.

expert reply by: Jameson C

0

Answer 1

Hi Jim; according to the instructions for the #24870 all you have to do is lower the muffler to install the hitch. Lowering it and supporting it with a strap will be adequate. However, if you're having trouble getting it into place with the…

view full answer...

Answer 2

The answer to that is our manufacturers design a hitch to fit the vehicle and then do the best they can to make it as strong as possible and rate it independently from the vehicle. This is why we end up with higher rated hitches like the Curt #C11427…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Hello Mike, thanks for reaching out. We do offer a few different hitches for the 2026 Subaru Crosstrek, the Curt #C22MJ, the Draw-Tite #76209 and the EcoHitch #EH57CR. All 3 of these hitches place the receiver in virtually the same position beneath…

view full answer...

Answer 7

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 8

Good morning to you as well Steve, and congrats on your new van! I would be more than happy to make a recommendation for you! The best hitch for your 2026 Toyota Sienna, is going to be our etrailer item #e56RR. This is a class III hitch with a…

view full answer...

Answer 9

Hi John! We definitely have hitches available for your 2026 Lexus RX350h and the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e29ZV is a great option. The matte finish makes our hitches blend in better than…

view full answer...

Answer 10

Thanks for supporting a local business Christopher! So long as your 2012 Chevrolet Silverado is a 1500 and you need a class IV hitch, the Curt item #14301 is going to be the best option. It has a 2" receiver with a 10,000 lbs towing capacity and…

view full answer...

Answer 11

Hi Barbara! The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C33MJ will indeed fit your 2026 Mazda CX-50 Hybrid. It actually fits all version of CX-50 for this model year, so you are definitely good to go with it. Even with the PP,…

view full answer...

Is There Fascia Trimming Required to Install the Curt Hitch # C11427 on a 2011 Toyota Avalon

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching