Will the Curt # C73DR Fit My 2022 Lexus RX 350 AWD?

Question

Question:

I am a repeat customer who has been happy with your service and quality! I see you show the Curt C73DR listed for the Lexus RX-350. I have a new 2022 RX-350 AWD. Will this hitch fit the AWD version? If not, do you have a hitch that does? Thank you!

asked by: Rodney C

0

Expert Reply:

Thanks so much for purchasing with us! As far as the fitment, the Curt Trailer Hitch Receiver - Custom Fit # C73DR will fit your all-wheel drive version of 2022 Lexus RX 350. It fits all versions except the F-sport version.

If you need assistance with installing the hitch, I went ahead and included an attachment of the installation instructions for you.

If you have an idea about how you wish to use your hitch, feel free to provide me with your needs and I will be happy to recommend the best products.

Congrats on the new car!

expert reply by: Bob C

0

Answer 1

We do have a hitch that will fit your 2022 Lexus RX 350 with the Curt #C73DR. This hitch will still allow you to use your liftgate sensor, but you will need to kick to either side of the receiver as opposed to just swiping your foot under the bumper.…

view full answer...

Answer 2

Hey Steve! Welcome back and congrats on the new SUV. To add a hitch and 4-way wiring harness to your new 2026 Mazda CX-5, you'll need the following parts: Hitch - Curt item #C72RJ 4 -Way Wiring Harness - Curt item #C45FV The Curt Hitch item…

view full answer...

Answer 3

Hey Peter, congrats on the new SUV. The Curt Trailer Hitch item #C72RJ is the correct hitch for the 2026 Mazda CX-5. There is no trimming required for installation. The Curt Hitch item #C72RJ is a class III hitch with a 2" receiver. It is custom…

view full answer...

Answer 4

Hey Rick, this is a great question but you would need to leave the tie down off of your 2026 Lexus RX350 when installing the etrailer hitch part #e29ZV. Its not needed but if you were to somehow need to recover the vehicle you could use the…

view full answer...

Answer 5

I recommend the Curt Adjustable Width Trailer Hitch Receiver #13703. This receiver will allow you to bolt to an RV frame between 22" and 72" wide. You will need to drill the mounting holes for the frame along with holes in the receiver…

view full answer...

Answer 6

Hello Chet, That is correct, you won’t need to remove the underbody or trim any part of your vehicle. The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C73DR is a super simple install. The only thing you’ll need to remove is a…

view full answer...

Answer 7

Hey Bob. To install the ground on the Curt T-Connector Vehicle Wiring Harness item #C36PQ you'll want to find a flat metal spot near the converter. You can take a wire brush and clear away the paint to ensure you reach bare metal. Then you'll…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Will the Curt # C73DR Fit My 2022 Lexus RX 350 AWD?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching