Is there a Hitch and 4-Way Trailer Wiring for a 2026 Mazda CX-5?
Updated 07/25/2026 | Published 06/23/2026 >
Products Featured in This Question
Question:
Good morning, What hitch and 4way wiring harness do I need for a 2026 Mazda CX-5? Thank you
asked by: Steve
Expert Reply:
Hey Steve! Welcome back and congrats on the new SUV. To add a hitch and 4-way wiring harness to your new 2026 Mazda CX-5, you'll need the following parts:
Hitch - Curt item # C72RJ
4 -Way Wiring Harness - Curt item # C45FV
The Curt Hitch item # C72RJ is class III hitch with a 2" receiver, that has a 2,000 lbs towing capacity and a maximum tongue weight of 200 lbs. It'll work great for towing a small trailer or hauling an accessory like a bike rack or cargo carrier. This custom fit hitch comes with all hardware necessary for the installation.
The Curt 4-Way Wiring Harness item # C45FV is also custom fit. It's going to plug in behind your Mazda's rear tail light assemblies. You will not have to cut or splice any wires to complete the installation. It's going to provide you with a 4-way connector capable of controlling your trailer or accessories lighting functions.
If you plan on towing you'll also need the Trailer Valet Ball Mount w/ 2" Ball item # TV37ZR. This ball mount comes with a pre-installed 2" hitch ball along with a hitch pin and clip.
What do you plan on using your new hitch for?
You can add this information, along with any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Search Results: 13515
- Shop: Trailer Wiring
- Search Results: circuit breaker
- Search Results: 13520
- Shop: Front Mount Hitch
- Shop: Stealth Hitches Hidden Rack Receiver - Custom Fit - 2"
- Shop: Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Black
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Brake Controller
- Article: My Trailer Hitch Doesn't Fit
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: B&W Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: c56rj
- Video: The Low-Down on the etrailer Hitch Pin Alignment Collar for Hitch Accessories
- Video: 2019 Jeep Wrangler Unlimited - Curt T-Connector Vehicle Wiring Harness Set Up
- Video: Easily Install Your Curt Trailer Hitch - 2026 Chrysler Pacifica
- Q&A: Recommended Hitch for a 2026 Mazda CX-5
- Video: How to Put On Your Curt Class III Trailer Hitch - 2023 Chrysler Pacifica
- Q&A: Will the Curt T-Connector Wiring for a 2024 Ford Ranger Work Without OEM Tow Package?
- Q&A: Is Wire Needed for Brake Controller Wiring Kit # ETBC7L on 2015 Hyundai Santa Fe Limited Ultimate
- Q&A: How to Locate the Reverse Light Wire on the Back of a 2017 Toyota Highlander
- Q&A: How Does Curt TriFlex NEXT Brake Controller Mount
- Video: Installing the Curt Front Mount Trailer Hitch Receiver on a 2015 Toyota 4Runner
- Q&A: Can 12 Volt Power Source for Brake Controller Install Kit # ETBC7L Run to Alternative Circuit
- Q&A: Plug And Play Trailer Connector 4 Way Flat For 2026 Volkswagen Tiguan
- Video: Beginner’s Guide to Installing the Curt Front Mount Trailer Hitch Receiver on a 2012 Toyota 4Runner
- Search Results: trailer hitch ball mount





Steve
7/25/2026
Thank you so much! I plan on renting a U-Haul trailer to take my daughter and all her stuff to college in Mississippi next month.