Compatible Frame Size for Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels F27CR

Question

Question:

What are the measurements of the plate the bolts go through? I have a handmade trailer and need a plate that measures at least 6.5 inches on at least one side.

asked by: Hailey

0

Expert Reply:

The Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels part # F27CR is designed for 3" x 3", 3" x 4", or 3" x 5" trailer frames. The largest frame size we have a bolt-on jack for is 3" x 6", the Extreme Off-Road Swing-Up Trailer Jack with Dual Wheels part # ORJW750BD. If you have a larger frame you'll have to go with a weld-on option which I have attached a list of below.

It sounded like you were looking for a reference to frame size but I wasn't quite sure so if this was not the info you were looking for please just let me know and I will try to do a better job of assisting.

expert reply by: Conner L

0

Answer 1

Hey Dale. I really like the Ark Xtreme Off-Road Jack w/ 2 Wheels item #ARK99FR you were looking at. It's got treaded rubber wheels instead of formed plastic so it cuts through mud and gravel pretty easily. It bolts to trailer frames 2" to…

view full answer...

Answer 2

Hey Greg, what's interesting about the Ark Xtreme Off-Road Jack #ARK99FR that you referenced is that number you can adjust the height of the jack relative to the mounting bracket by pulling out on the handle so even if you had a clearance issue…

view full answer...

Answer 3

Hey Rod, The Ark Xtreme Off-Road Jack w/ 2 Wheels #ARK99FR has multiple slots in the outer tube of the jack that the mounting bracket can slot into. In the bottom slot you'd be right around 9-1/2" between the ground and frame with the wheels…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 6

Hi Brett! Good question. Took me a minute to figure it out, but the Ark Xtreme Off-Road Tube Mount Swivel Trailer Jack- Sidewind - 18" Lift - Black - 1,650 lbs #ARK47FR can actually be taken completely off the tube mount (see included image) and…

view full answer...

Answer 7

Hello Chris, thanks for reaching out. I went out to our warehouse and measured the etrailer Base Plate #e74FV. The thickness of the tabs is 0.45". The Distance between is 0.625" or 5/8". The pin hole is a 1/2" diameter. This base…

view full answer...

Answer 8

Hey Justin, welcome back! I can help with that. For the Ark Jacks #ORJW750BD and #ORJW750D, the only difference between the two is the color. The BD is black and the D is silver. Aside from the finish they are the same 1,650 lb capacity 18" lift…

view full answer...

Answer 9

Hey George, best solution for you will be to go with an all new jack like the etrailer part #e95YV because Fulton is no longer in business so there isn't a way to get a replacement F2 and none of the other jacks out there use the same bolt…

view full answer...

Answer 10

Hey Peter, Yes, the #ARK39FR is the XL version of the #ORJW750BD, and you’re right that it has a maximum height of 34", which is shown on the product page. That said, thanks for catching the error in the description where it lists 4 adjustment…

view full answer...

Compatible Frame Size for Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels F27CR

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching