Determining Which Replacement Trailer Jack Fits Dorsey Malibu Boat Trailer

Question

Question:

I need to replace the trailer jack to my Dorsey Malibu Boat Trailer. Serial Number 4TBBT21162K000652. You can see the jack part with the wheel bent. There was a lot of play with the jack either down to raise or lower the trailer, or in stowed. It locked but not very well, which is how this bent. Thanks.

asked by: Derek R

0

Expert Reply:

I would be happy to help, but I have no way of looking your trailer by the serial number to determine which replacement side mount jack is correct.

Based on the picture you provided of the jack on your Dorsey Malibu Boat Trailer a standard bolt on jack like the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels # F27CR may likely work as it mounts to the trailer bracket with a center bolt like your jack.

You can confirm this by comparing the dimensions of your trailer jack mount to the picture of the mount included with the # F27CR. As long as the bracket matches this would be a great option. This specific jack offers 12" of lift and has a 1500lb weight capacity.

If you find your bracket has a different pattern just let me know.

I included a video of the # F27CR for you to take a look at.

expert reply by: Samuel C

0

Dimensions Of Mount Plate For Fulton XLT Jack # F141133
(click to enlarge)

Customer Picture
(click to enlarge)

Answer 1

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 2

Yes. The bolt patterns that were referred to in the videos are actually the same and in reality the .06" is a negligible difference that falls within a reasonable margin of error; I believe that on the #F1413050334 measurements were performed…

view full answer...

Answer 3

While we do have some great U.S.A.-made boat trailer jacks, the etrailer Round Swivel Marine Jack #MJ-1500B-DWL is manufactured in China. However, for a super close U.S.A.-made model, I recommend the Dutton-Lainson Swivel Marine Jack #DL67MR. This…

view full answer...

Answer 4

I have included a dimensional drawing of the Dutton-Lainson Round Swivel Jack #DL22335 that shows the overall extended height of the jack at 40-5/8" tall. This measurement is from the bottom of the wheel to the top of the jack when extended.

view full answer...

Answer 5

For a marine jack with the mounting dimensions you need, I recommend the Fulton Blot-Thru Swivel Marine Jack with Caster #FXP10. This jack has the 3-1/2 inch x 5-1/2 inch mounting bolt pattern to fit to the existing mounting plate on your trailer. I…

view full answer...

Answer 6

Let's start with the brake controller. My personal recommendation is for the Tekonsha Prodigy P3, #90195. This is a customer favorite because of how easy it is to setup and how well it works. Now for the wiring. Although your 2008 Monaco Knight…

view full answer...

Answer 7

Since you have checked it out and are unable to find a wire at the top of your brake pedal, you will need to find a dedicated circuit as you described. If your third brake light only works when the brakes are applied you can use that wire for your…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Determining Which Replacement Trailer Jack Fits Dorsey Malibu Boat Trailer

Featured Help Information

Miscellaneous Media

Continue Researching