Demco Highjacker Replacement Pin Size

Question

Question:

Hi, I need to replace the pins that hold the hitch into the rails. Can you confirm the size of the pins length and diameter that I should be using? Thanks!

asked by: Bill B

1

Helpful Expert Reply:

I spoke with Demco, and they confirmed the Replacement Pin and Clip for Demco Hijacker Autoslide 5th Wheel Trailer Hitch # DM92VR which measures at 1/2" x 3" is is the correct part for your Demco Hijacker Autoslide 5th Wheel Hitch # DM8550034.

expert reply by: Bryce D

1

Answer 1

We always recommend a sliding hitch for a bed length less than 8' but you can do a little bit of measuring to see just how much turning clearance you have with your 2022 Keystone RV Cougar 368MBI with a MaxTurn nose and determine if a sliding…

view full answer...

Answer 2

Hey Terry we have a fifth wheel rail kit that fits your 1994 Chevy K1500 and your Valley fifth wheel hitch with the B and W part #BWRVK3200. Thankfully Valley made their hitches to fit the industry standard fifth wheel rails like what the B and W kit…

view full answer...

Answer 3

We do not carry any replacement parts for Valley hitches, and they are unfortunately not in business anymore. With that being said, the replacement part you're needing is not going to be available, however I do have an alternative solution. Since…

view full answer...

Answer 4

All the brake controller needs to sense a trailer connection so that you can test it is a slight amperage draw on the output circuit. For that you can use a circuit tester like the part #PTW2993 with one pin grounded and the other on the output pin.…

view full answer...

Answer 5

We don't offer a video, but that's a great idea that I'll suggest to our shop manager. The maintenance procedures for the Demco #DM8550040 Hijacker Autoslide 5th wheel hitch are outlined in the linked owner's manual, but the keeping…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 11

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Demco Highjacker Replacement Pin Size

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching