Which Mounting Kit Is Correct For Installing Westin 3" Running Boards On 2003 Silverado 2500HD?

Question

Question:

Will this hardware fit a 2003 Silverado, 2500 HD with an extended cab. I have 3 inch platinum series bars. Thanks

asked by: Michael M

0

Expert Reply:

It looks like you have Westin Round Nerf Bars - 3" - Chrome Plated Steel # 25-1950 installed on your 2003 Chevy Silverado 2500HD extended cab. In this case, you will want to go with Replacement Installation Hardware Kit for Westin Platinum series Round Nerf Bars # 25-195PK.

expert reply by: Andrew N

0

2003 Silverado 2500HD With Westin 3" Running Boards
(click to enlarge)

Answer 1

Yes, the Westin E-Series 3-inch black nerf bars #23-1955 that you referenced do fit both of the trucks you mentioned. These steps fit the 2012 GMC Sierra 2500 Crew Cab; they also fit the 1500 and 3500 Crew Cabs. They also fit the 2008 Sierra Crew…

view full answer...

Answer 2

Thanks for the picture of your truck! Looks like you have the Westin steps part #25-1955 installed and that means the correct replacement hardware kit is #25-195PK. Must have been a huge hog to mess up the brackets that bad!

view full answer...

Answer 3

The hardware kit for the Platinum series round nerf bars on your 2007 GMC Sierra is the Replacement Installation Hardware Kit for Westin Platinum series Round Nerf Bars Item #25-195PK. This kit fits the 2007 GMC Sierra 2500 new body style and the…

view full answer...

Answer 4

If the Westin bars you have originally did fit your 2006 Chevy Silverado the correct replacement install hardware would be the part #23-195PK. If the bars came off of a different truck though they would not be able to fit your truck by just swapping…

view full answer...

Answer 5

If the 3 inch diameter nerf bars were Westin brand bars and they initially came off of a 2003 GMC Sierra Extended Cab then yes the install kit part #23-195PK would fit and work great.

view full answer...

Answer 6

Do you know the cab length/style of your truck and possible which Westin bars you have?

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Which Mounting Kit Is Correct For Installing Westin 3" Running Boards On 2003 Silverado 2500HD?

Product Page this Question was Asked From

Continue Researching