What is the Weight of the Draw-Tite Hitch # 75471?

Question

Question:

How much does the product weigh?

asked by: Keith

0

Expert Reply:

The weight of the Draw-Tite Max-Frame Trailer Hitch Receiver # 75471 is 43 pounds. If you need assistance with accessory recommendations for your hitch, I would be happy to assist you.

expert reply by: Bob C

0

Answer 1

Minus packaging, the Draw-Tite #75673 Class III trailer hitch weighs about 32 lbs, and is a confirmed fit for your 2013 Subaru Outback Wagon. You might consider the less expensive Curt #C13410 Class IIl as well. The Curt hitch features a concealed…

view full answer...

Answer 2

The size ball you need will depend on what the trailer coupler requires. If you look at the top of the coupler it should say the size ball it requires. Also, you will need a ball with the correct diameter shank to fit the ball hole in the ball mount.…

view full answer...

Answer 3

Absolutely! The Draw-Tite Ultra Frame Trailer Hitch Receiver #41945 you were looking at for your 2008 Ford E-350 weighs in at 48lbs. I included a video of the #41945 being installed for you to take a look at.

view full answer...

Answer 4

The protective black powder coat finish on a Curt or Draw-Tite hitch like #C13119 does eventually break down from exposure but this is not considered a warranty issue. This normal wear and tear can best be addressed by applying a new layer of…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C11576 which fits your 2019 Toyota Camry comes with what is referred to as a powder coat finish. A powder coat finish is similar to paint in look but is much more weather resistant. I do not have any quantitative…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

What is the Weight of the Draw-Tite Hitch # 75471?

Featured Help Information

Miscellaneous Media

Continue Researching