Weight of Draw-Tite Class III 75673 Trailer Hitch for 2013 Subaru Outback Wagon

Question

Question:

How much does the Draw-Tite 75673 Class III hitch for a 2013 Subaru Outback weigh?

asked by: LR

0

Expert Reply:

Minus packaging, the Draw-Tite # 75673 Class III trailer hitch weighs about 32 lbs, and is a confirmed fit for your 2013 Subaru Outback Wagon. You might consider the less expensive Curt # C13410 Class IIl as well. The Curt hitch features a concealed design that hides the hitch crossbar behind the bumper for a cleaner appearance. I've linked to install video for both hitches, so you can compare what both hitches look like once they're installed. The Curt hitch weighs about 5 lbs less than the Draw-Tite.

If you'll be using the hitch for towing, you'll need a few more items to complete your setup. For a trailer wiring harness, use # 118467. For a ball mount, use # C45030 and # 19261 for a 1-/78 or # 63845 for a 2 inch trailer ball. You will also need a pin and clip like # PC3.

I've also linked to an install video for the trailer wiring harness.

expert reply by: Mike L

0

Answer 1

The size ball you need will depend on what the trailer coupler requires. If you look at the top of the coupler it should say the size ball it requires. Also, you will need a ball with the correct diameter shank to fit the ball hole in the ball mount.…

view full answer...

Answer 2

Absolutely! The Draw-Tite Ultra Frame Trailer Hitch Receiver #41945 you were looking at for your 2008 Ford E-350 weighs in at 48lbs. I included a video of the #41945 being installed for you to take a look at.

view full answer...

Answer 3

The weight of the Draw-Tite Max-Frame Trailer Hitch Receiver #75471 is 43 pounds. If you need assistance with accessory recommendations for your hitch, I would be happy to assist you.

view full answer...

Answer 4

The Curt Trailer Hitch Receiver part #C11576 which fits your 2019 Toyota Camry comes with what is referred to as a powder coat finish. A powder coat finish is similar to paint in look but is much more weather resistant. I do not have any quantitative…

view full answer...

Answer 5

The protective black powder coat finish on a Curt or Draw-Tite hitch like #C13119 does eventually break down from exposure but this is not considered a warranty issue. This normal wear and tear can best be addressed by applying a new layer of…

view full answer...

Answer 6

I do have a 2 inch hitch that is a no-drill installation for your 2016 Subaru Outback. It is the Curt #C13410. These hitches are getting very popular with Subaru owners. I have linked a video showing an example installation for you. Although the…

view full answer...

Answer 7

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 8

Both the Draw-Tite Max-Frame Trailer Hitch Receiver #75673 and the Curt Trailer Hitch Receiver #C13206 will require drilling to install on your 2017 Subaru Outback Wagon. It is only a 1-1/8" access hole though so it is pretty minimal. The reason…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The Curt #C13410 and Draw-tite #76227 are very similar in design and both have the same weight ratings of 600lbs tongue weight and 4,000lbs of trailer weight. I do like that Draw-Tite does add the additional plate of steel in between the hangers that…

view full answer...

Answer 11

Hi John; I'd definitely get a frame-mounted hitch for your 2017 Subaru Outback to tow a small camper. I'm not aware of a bumper-mounted hitch for your Outback, but if there were one I definitely wouldn't trust it for towing purposes.…

view full answer...

Answer 12

Both the Curt #C13382 and the etrailer #e98912 hitch are a 2" Class III hitch receiver that will provide a maximum gross trailer weight of 3,500 lbs and a maximum tongue weight of 525 lbs. You are correct, they are an identical hitch but our…

view full answer...

Weight of Draw-Tite Class III 75673 Trailer Hitch for 2013 Subaru Outback Wagon

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching