Will Timbren part# TGMRCK25S fit on a 2007 Chevy Silverado Classic 3500

Question

Question:

Ity doesnt specify if it will fit a 3500 Classic Chevy. Is there a difference between the 2500 and the 3500?

asked by: Jeff K

0

Expert Reply:

The difference between the 2007 Chevy Silverado 2500 and the 3500 series trucks is the weight capacity. The 3500 is going to have a higher weight capacity than the 2500.

I spoke with the engineer at Timbren and he told me that the TImbren part # TGMRCK25S will fit on your 2007 Chevy Silverado Classic 3500, because the Timbren springs for the 2500 and 3500 models will install the same way on both truck models. These springs were tested up to 6,000 pounds and work well within those guidelines. Keep in mind that these springs do not increase the weight carrying capacity of your truck. You should not exceed the weight capacity specified by your Chevrolet Truck owners manual.

For the comparable Timbren springs for the 3500 model is part# TGMRCK35S. These springs were tested up to 8,600 pounds. Again, keep in mind, these do not increase the weight carrying capacity of your truck.

I have attached a Timbren Suspension Enhancement Systems article that may assist you when installing your system.

expert reply by: Lori W

0

Answer 1

Where you'll attach the pivot arms on the B&W Patriot #BWRVK3255 just depends on how much clearance you need from the cab of the truck, but in most cases you'll be just fine using the closest setting to the cab. You'll want to make…

view full answer...

Answer 2

I'm happy to help you with that application. For your 2000 GMC Sierra 2500 4WD there are three SumoSpring options for your truck. If you will be doing normal towing and payloads then I recommend the SumoSprings Solo Custom Helper Springs…

view full answer...

Answer 3

Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…

view full answer...

Answer 4

If your 2002 Chevy Silverado 1500 is leaning to the left, I assume you have come to us because you are carrying a heavy load and this is when it is occurring. If so, we have exactly what you need to fix the issue; if it is happening at all times you…

view full answer...

Answer 5

I attached a picture that shows how the Timbren #TGMRTT35D that you referenced gets assembled. The spacer #TA25722-90P00 you referenced would go between the numbers 2 and 3 and you'd be set. See attached picture. You will need to provide a longer…

view full answer...

Answer 6

Timbrens would be the way to go since you are hauling quite a bit of weight. So for your 2008 Chevy Silverado 2500 you'd want the part #TGMRCK25S which can give you up to an additional 6,000 lb of suspension support. You should note that this kit…

view full answer...

Answer 7

The GVWR is the gross vehicle weight rating. This is the most the vehicle can weigh including cargo, passengers, gas, everything. The GAWR is the gross axle weight rating which is 3,950 pounds for the front and 3,750 for the rear. The cargo weight…

view full answer...

Answer 8

The kit you referenced is actually designed for heavier duty versions of the Silverado like the 2500 and the 3500. I wish SumoSprings offered lift spacers for their kits but they do not currently. Best solution will be to use the #TGMRCK25S which…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hello Mel, great question! Yes, the Torklift tie downs part #TL66FV will fit your 2006 GMC Sierra 2500HD crew cab with the 8 foot bed, provided your truck does not have running boards or cab length boards that extend under the bed, and you are not…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Will Timbren part# TGMRCK25S fit on a 2007 Chevy Silverado Classic 3500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching