Is the Draw-Tite Hitch for a 2021 Toyota Venza Hidden

Question

Question:

Will the cross bar on this item show after installation? By show I mean would a following car or person standing behind the vehicle notice it? Also, will it require moving the exhaust system to install?

asked by: Andy E

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # DT46MR for a 2021 Toyota Venza has a hidden design which means the crosstube is concealed behind the bumper and cannot be seen from outside the vehicle. It does require the muffler be lowered, not removed but most hitches do require lowering of the exhaust.

expert reply by: Conner L

0

Answer 1

Hi Steven! Most of the hitches available for a 2022 Toyota Venza will fit a RAV4 as well, but not all of them. The Curt #C77MJ and EcoHitch #EH97FR will fit both models, but the Draw-Tite #DT46MR will only fit the Venza and Draw-Tite #DT82QR will…

view full answer...

Answer 2

Hey Aniki, the B and W hitch part #BW47BR has the same ground clearance dimension as the Curt #C77MJ, 12 inches. Are you worried about dragging?

view full answer...

Answer 3

Hi Eric! The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C77MJ will definitely fit your 2025 Toyota RAV4 Hybrid. I included a picture of it on a 2025 RAV4 Hybrid to 100% cement that absolutely certain fact. : ) For the wiring, I…

view full answer...

Answer 4

That is a great question. We do carry two trailer hitches for your 2023 Toyota Venza. The #C89UR is made by curt, the #e25AR is our etrailer brand which is actually made by Curt. So both hitches are going to be identical as far as weight capacity and…

view full answer...

Answer 5

Yes, the Kuat Sherpa 2.0 #SH12G will clear the bumper on your 2021 Toyota Venza if your measurement from the center of your hitch pinhole to the end of your bumper is approximately 6 inches. The measurement of the length of the shank's pinhole to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Is the Draw-Tite Hitch for a 2021 Toyota Venza Hidden

Continue Researching