Rear Torklift Truck Bed Camper Tie Downs for 2001 Ford F350 With Factory Hitch

Question

Question:

Hello Looking to purchase rear tie downs for my 2001 f350 dually that has the factory installed hitch. Just want to make sure the TLT3303 are the correct ones for my truck

asked by: Jack H

0

Expert Reply:

Although the # TLT3303 tie-downs aren't a fit for your 2001 Ford F350, we do have a rear tie down fit that's compatible with a factory hitch. For a steel tie-down, use # TLF3001 or # TLF3001A for an aluminum/stainless tie down.

expert reply by: Mike L

0

Answer 1

The 2-1/2 inch opening is not going to be a problem. The rear tie downs, #TLF3001, come with a sleeve that fits around the outer tube and inside of the open ends of the hitch on the truck. With the sleeve on the width of the outer tube becomes 2-1/2…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hey Steve, thanks for reaching out! The Roadmaster Direct-Connect Base Plate Kit #RM87NQ fits your 2025 Ford Maverick as long as it's the Hybrid model that doesn't have the engine block heater. It doesn't come with the 6-Pin connector,…

view full answer...

Rear Torklift Truck Bed Camper Tie Downs for 2001 Ford F350 With Factory Hitch

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching