How Many Studs Come with the Replacement Wheel Studs?

Question

Question:

How many studs come with this item?

asked by: Laramie H

0

Expert Reply:

The Replacement Wheel Stud, Screw-In, 1/2" x 2" # 25-53 only includes one of the replacement wheel studs.

expert reply by: Bob C

0

Answer 1

It looks like a Hayes Brake magnet part number 73400. We do not carry this part but I did a quick internet search and was able to find a couple places that sell them. From the research I did it looks like this is an older style of brake magnet used…

view full answer...

Answer 2

Hello Robert, thanks for reahcing out. Those 185100-150 brakes you mentioner are an older part that has been discontinued. We sold our last ones early 2024 and we will not be getting more stock. We do still have the Dexter Electric Trailer Brakes…

view full answer...

Answer 3

The Replacement Entry Door Hinge for RV #LC198295 has a standard leaf design that fits most RV's. The overall length is 9-1/4", and each leaf measures from 2-1/8" to 2-1/2" wide. As long as your current hinge has this much space…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

Thanks for the photo. It appears you have just a standard manual lift vent, so my recommendation is to use the Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - White #V2092SP-28 or smoke colored cover #V2092SP-29. These…

view full answer...

Answer 6

For what you have you'd want the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies #AKEBRK-7-SA and you'd be set. This is a set of self adjusting brake assemblies that fit your axle/hub and will work…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

How Many Studs Come with the Replacement Wheel Studs?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching