Replacement Brake Assemblies for Trailer with Kelsey Hayes Brake Set

Question

Question:

Hi, I have an old trailer with 2 axles. One axle has brakes with KHRH and KHLH stamped on them and nothing else. I assume theyre Kelsey Hayes right and left hand brakes. Theyre attached to the axle with 5 bolts and they have 6 lug, 16 wheels on the axle. Do you have new brake kits that would fit this? Drums are fine. Thanks,

asked by: Matt J

0

Expert Reply:

For what you have you'd want the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies # AKEBRK-7-SA and you'd be set. This is a set of self adjusting brake assemblies that fit your axle/hub and will work great.

expert reply by: Jameson C

0

Answer 1

For your trailer, you can reuse the bearings and hubs as long as they are in good working condition. For your brake assemblies I recommend the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K…

view full answer...

Answer 2

The Replacement Wheel Stud, Screw-In, 1/2" x 2" #25-53 only includes one of the replacement wheel studs.

view full answer...

Answer 3

It looks like a Hayes Brake magnet part number 73400. We do not carry this part but I did a quick internet search and was able to find a couple places that sell them. From the research I did it looks like this is an older style of brake magnet used…

view full answer...

Answer 4

Hello Robert, thanks for reahcing out. Those 185100-150 brakes you mentioner are an older part that has been discontinued. We sold our last ones early 2024 and we will not be getting more stock. We do still have the Dexter Electric Trailer Brakes…

view full answer...

Answer 5

Since the trailer was off of the ground it would not take much voltage to stop the wheels from spinning so they may be getting power but they may not be getting enough power due to a short or wiring issue. But 9 times out of 10 weak trailer brakes…

view full answer...

Answer 6

The Dexter Electric Brake Kit #23-105-106-09 is currently the only 12" brake kit we carry which utilizes the 4 bolt flange for the Kelsey Hayes axles. It was created with the 5 bolt pattern as well so that it could be used for more than just the…

view full answer...

Answer 7

The Hadco 322 is obsolete and no longer around. I don't have any information on the bearings it uses either, so you will need to identify the bearings to see if there is a possible replacement. You can look to see if the part number is stamped in…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The Replacement Entry Door Hinge for RV #LC198295 has a standard leaf design that fits most RV's. The overall length is 9-1/4", and each leaf measures from 2-1/8" to 2-1/2" wide. As long as your current hinge has this much space…

view full answer...

Answer 10

Hi Pedro; nothing comes back under that part number. Based on the information you provided I'm guessing you need the Dexter Electric Trailer Brakes - 12" - Left/Right Hand - 6K AL-KO/Hayes Axles #23-105-106-09. These are 12" x 2"…

view full answer...

Answer 11

The etrailer.com Self-Adjusting Brakes #AKEBRK-35-SA will replace both brakes on an axle, but do not come with the hubs. That being said, if the hubs are in good condition, they will not need to be replaced. When you remove the hub, you will need to…

view full answer...

Answer 12

That is a neat looking camper. 1989 was a good year. Honestly, the same answer will apply to the brakes on your 1989 Silver Streak Travel Trailer. The 12" x 2" brakes are still standard. We will just need to make sure that the brake…

view full answer...

Replacement Brake Assemblies for Trailer with Kelsey Hayes Brake Set

Product Page this Question was Asked From

Continue Researching