Measurements For Adjustable Width Trailer Hitch Receiver for RVs

Question

Question:

What is the dimension from face of receiver to back of crossbar on the Curt #13702 hitch

asked by: Charles P

0

Expert Reply:

The distance from the back of cross tube to the face of the hitch tube on the Adjustable Width Trailer Hitch Receiver, # C13702 is 8-3/4". Please see the product review video that is attached.

expert reply by: Michael R

0

Answer 1

The distance between the bolt holes from side-to-side on the Buyers Products Hitch Plate with Receiver Tube #3371809067 are 35.05 inches apart. The height of the mounting flange is 6-1/2 inches. The distance between the bottom of the flange to the…

view full answer...

Answer 2

I checked with Curt and was able to find a couple of diagrams of the mounting bracket and the receiver portion for the Adjustable Width Trailer Hitch Receiver item #13703. I have attached them below. The width is adjustable between 22" and…

view full answer...

Answer 3

The frame not being exposed isn't a big issue since it's just covered up with some corrugated plastic sheeting that can easily be pulled down and cut to fit in accessories. The real issue is going to be with the bumper since it sits right…

view full answer...

Answer 4

The cross tube on the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide #C13704 is 68.5 inches from tip to tip without the hanging brackets. It has a max weight capacity of 5000 pounds and a max tongue weight of 500 pounds.…

view full answer...

Answer 5

Thanks for the pictures! 2" hitches do not all have a 5,000 lbs capacity. The capacity varies by vehicle. That is an old Reese 06497 hitch and the sticker is correct. It does indeed top out at 3,500 lbs. It looks like this hitch came on all of…

view full answer...

Answer 6

Hey David, Those part numbers unfortunately didn't come back to anything so the next step would be measuring the width of the frame rails and seeing how much of a drop would be needed to clear the rear fascia. For example, the Curt #C13702 you…

view full answer...

Answer 7

The distance from the two bolt holes on each side bracket for the Curt Adjustable Width Trailer Hitch Receiver #C13702 is right at 8-5/8" (center to center). I have also attached a diagram to assist. This adjustable hitch will fit frame widths…

view full answer...

Answer 8

If you are looking for a trailer hitch to mount on your RV then the highest rated capacity is the Curt Trailer Hitches parts #C13702 and #C13701 which are both rated for a max of 6,000 lbs towing when a weight distribution (WD) system is used. These…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Measurements For Adjustable Width Trailer Hitch Receiver for RVs

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching