Trailer Hub Bearing Kit for 2019 Flagstaff Super Lite 26RLSW Dexter 3722505 Axle 4k

Question

Question:

What bearing kit do I need for this axle? 2019 Flagstaff Super Lite 26RLSW Dexter 3722505 4000 lb axle Thank You

asked by: Joe S

0

Expert Reply:

For the Dexter 4,000 lb trailer hubs the bearings are # 25580 for the inner bearing and # LM67048 for the outer. So for a kit that has both you'd want the # BK3-310.

expert reply by: Jameson C

0

Answer 1

Realistically it is best to stick with a Dometic replacement thermostat for your Dometic setup. The #DMC79FR is the correct replacement for your 3316410.012. It may be possible to use a universal thermostat like the #CAM09221 you looked at but this…

view full answer...

Answer 2

In order to find the correct bearings, you'll need to remove a hub and read the reference numbers off the inner and outer wheel bearings. If you cannot read the reference numbers, use a digital caliper and measure the inside diameter of the inner…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Trailer Hub Bearing Kit for 2019 Flagstaff Super Lite 26RLSW Dexter 3722505 Axle 4k

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching