BB&W Rubber Cover for Empty Turnoverball Socket

Question

Question:

Will this plug compress down with the bedrug installed?

asked by: Chris

0

Expert Reply:

The B&W Rubber Cover for Empty Turnoverball Socket, # BWGNXA1715, is made specifically for use with B&W for socket in truck beds that do not allow you to store your Turnoverball in place. This will not compress.

expert reply by: Michael R

0

Answer 1

Hey Rob! You can actually use either one, but my recommendation would be the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches #BWGNRK1320-5W. B&W makes some of the best hitches available, and the Turnoverball is no…

view full answer...

Answer 2

While the Convert-A-Ball Cushioned 5th-Wheel-to-Gooseneck Adapter w/ Offset #CAB-C5GX1216 is compatible with the 4" Offset Ball #BWGNXA4685 do note this will void your chassis warranty and possibly any other warranties on your 5th wheel camper.…

view full answer...

Answer 3

While I can't say yes or no for if it will give you enough clearance I can give you the measurements so you can verify that you will have enough clearance for your Forest River Sierra 40002FB. First the 4" Offset Ball #BWGNXA4085 does give…

view full answer...

Answer 4

If you were to use the 4 inch offset ball #BWGNXA4085 the pin weight on the ball will not be changed. What will change is where the weight is carried on the truck. Using the offset ball will put more weight 4 inches back from the center of the…

view full answer...

Answer 5

Hey James! I'm not entirely sure what you're asking here. Do you want to know if you can use the #BWGNXA4085 with the additional height compared to your current ball? This ball is 5-3/4" tall from the base of the truck bed to the top of…

view full answer...

Answer 6

Hey Glenn, for the 2024 Ram 2500 Gen-Y only makes the 5 inch offset hitch ball for the OEM pucks with the part #GY83XR. There isn't a 4 inch version available as well but even if there was the 5 inch offset would be better since you'd get…

view full answer...

Answer 7

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

BB&W Rubber Cover for Empty Turnoverball Socket

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching