Battery Box Dimensions for Curt Push-To-Test Trailer Breakaway Kit

Question

Question:

Do you have dimensions for the battery box ?

asked by: Neil G

0

Expert Reply:

The overall dimension of the Curt Push-To-Test Trailer Breakaway Kit part # C52044 are 6-1/2" long x 4-3/4" wide x 5" tall. I have attached a review video for you which showcases all of these dimensions.

expert reply by: Conner L

0

Curt Battery Box Dimensions
(click to enlarge)

Answer 1

Yes! The only model we carry that is compatible with a 3-axle trailer and has a test light/charger on the battery case is the Curt Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Top Load #C52044. I went ahead and attached a demo…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Steve, thanks for reaching out! The Roadmaster Direct-Connect Base Plate Kit #RM87NQ fits your 2025 Ford Maverick as long as it's the Hybrid model that doesn't have the engine block heater. It doesn't come with the 6-Pin connector,…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hi Jerry, For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver #C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have,…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Battery Box Dimensions for Curt Push-To-Test Trailer Breakaway Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching