Solution for Holes of Draw Tite Hitch 75726 not Lining Up on Highlander

Question

Question:

Im interested in your Draw-Tite 75726 hitch for my 2010 Highlander SE 4WD. Ive read in several places that 1-2 of the holes do not line up and have to be enlarged. Has the mfg. addressed this ? Thank you.

asked by: Matt

0

Expert Reply:

The issue with the Draw Tite hitch part # 75726 not lining up with the holes on the vehicle like your 2010 Toyota Highlander is actually due to the hitch getting bent in shipping and not a design flaw. Unfortunately hitches are somewhat heavy and awkward to handle so shippers don't always handle them with enough care and the brackets can get bent and cause this issue. The hitch can be bent back and as long as there isn't creases or flaking paint you wouldn't have any problems.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite trailer hitch, #75726, will fit your 2008 Toyota Highlander with the factory OEM 19 inch full-size spare tire. There is a special note in the instructions which I have linked for you. The note states that when storing the spare, it is…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Aaron, great question! The Trailer Mate Trailer Hitch Receiver #TMT67FR is definitely a budget friendly option for a hitch on your 2026 Highlander. This is basically the economy line from Curt. The welds are a little different (but will still do…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Solution for Holes of Draw Tite Hitch 75726 not Lining Up on Highlander

Continue Researching