How To Install Draw-Tite Hitch On 2016 Mazda CX-5

Question

Question:

I’m looking at possibly the Draw Tite for our 2016 CX5. have a few questions about installing a hitch. - When installing a hitch, should the base be parallel to ground to the extent that I should use a spirit level to measure and tighten the nuts? Or, do I not need to worry about this aspect? - When choosing a drawbar and ball, is that based on the trailer tongue Im towing? - Is the torque specification absolutely necessary or can I just tighten? I do not own a torque wrench.

asked by: Kalyan

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76138 is a great option for a 2016 Mazda CX-5. In regards to install, you don't need to worry about angles or measurements, it uses preexisting holes in the frame so the hard work is done for you. The hardware does need to be torqued to spec but you can either buy a torque wrench from us part # PTW3001C or rent one from your local auto parts store which is usually free. I have attached a video below which will walk you through the process.

I have also attached for you below a help article that will go over how to select the correct ball mount. We do offer a general kit as well that works for most setups, etrailer Ball Mount Kit part # 989900.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 12

Hey Jerit, congrats on the new car. We've got a couple of hitches that fit the 2026 Subaru Crosstrek Wilderness. The etrailer Trailer Hitch item #e98912 is going to be the most affordable option. This custom fit class III hitch has a 2"…

view full answer...

How To Install Draw-Tite Hitch On 2016 Mazda CX-5

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching