Dimensions of Draw Tite Hitch 41906

Question

Question:

Draw-Tite 41906 Class V Ultra Frame Hitch Dimensions. So I can verify fit on my 2002 ford e350 shuttle bus. Width from mounting holes too mounting hole would be nice. Thanks

asked by: Kent S

1

Helpful Expert Reply:

I attached a picture that shows all of the relevant dimensions of the Draw Tite hitch part # 41906 that you referenced for you to check out and see if it would fit.

expert reply by: Jameson C

1

dimensions
(click to enlarge)

Answer 1

Hey Ozzie! The Weigh Safe Hitch w/ Built-In Scale for 2" Hitch #WS56KR has a 1" ball shank hole. You can use a ball like the Curt #40038 for a 2" or the #C40007 for a 2-5/16" ball. Just make sure the ball you use matches the 10k…

view full answer...

Answer 2

The 7" drop on the #4907 and 16" drop on the #4916 are measured from the top of the bracket to the center of the cross tube on the #41990. See the diagrams below. If you don't want to use either of these brackets you could also take the…

view full answer...

Answer 3

Hey Byron, thanks for reaching out! I recommend checking out the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07 because it's from the universal category so it can be adjusted to fit different circumstances. This does require…

view full answer...

Answer 4

The hitch you referenced, part #41906 is indeed a fit for your 1993 Ford E350. If you look at the photo I have edited for you, you can see the relevant dimensions of the Draw-Tite Class IV hitch, part #41906. I have provided you with the side-to-side…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hi Alex; the gauge on the Big Truck Big RV Tongue Weight Scale for Trailers #BTBRV004 has a +/- 5% full scale accuracy and displays weight in 20-lb increments up to 1,000 lbs. We also have it available with a SnapPad #BTBRV99FR. If you want something…

view full answer...

Answer 12

Hey Ed, welcome back! As long as the Big Truck Big RV Tongue Weight Scale #BTBRV004 is on a hard flat surface that does not flex it will work just fine. So you can use a spacer of some type to take up the extra space needed with this and it will work…

view full answer...

Dimensions of Draw Tite Hitch 41906

Continue Researching