Dimensions of Weld-On Brackets for Draw-Tite Ultra Frame Trailer Hitch 41990

Question

Question:

You mention a 7" or a16" , where are these measurements taken from

asked by: Steve

0

Expert Reply:

The 7" drop on the # 4907 and 16" drop on the # 4916 are measured from the top of the bracket to the center of the cross tube on the # 41990. See the diagrams below. If you don't want to use either of these brackets you could also take the # 41990 to a local fabricator and they can design something so it fits the way you want it to.

expert reply by: Robin H

0

4907 Bracket Dimensions.
(click to enlarge)

4916 Bracket Dimensions
(click to enlarge)

Answer 1

The mounting holes on the Draw Tite hitch part #DT45507 that you referenced are separated by 40 inches from left to right and the hitch opening will be 1-1/2 inches below the frame surface the hitch attaches to.

view full answer...

Answer 2

The best option we have for you to add a trailer hitch on your 1998 Shuttle Bus is the Draw-Tite Class IV Weld-On Ultra Frame Trailer Hitch Receiver #41990. This hitch can be installed with either 16 inch brackets #4916 or 7 inch brackets #4907. In…

view full answer...

Answer 3

I checked your order notes and it looks like your ordered the part #41990. You should note that this isn't intended as a front mount hitch and to install it you would normally want the part numbers #4907 for 7 inch brackets or part #4916 for 16…

view full answer...

Answer 4

At least 2 of your photos came through with the question, thank you for submitting those! Since there have been modifications made to your 1995 Chevrolet K3500, I cannot guarantee that a custom fit hitch for the 1995 K3500 cab/chassis will still fit…

view full answer...

Answer 5

Hey Byron, thanks for reaching out! I recommend checking out the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-07 because it's from the universal category so it can be adjusted to fit different circumstances. This does require…

view full answer...

Answer 6

Hey Ozzie! The Weigh Safe Hitch w/ Built-In Scale for 2" Hitch #WS56KR has a 1" ball shank hole. You can use a ball like the Curt #40038 for a 2" or the #C40007 for a 2-5/16" ball. Just make sure the ball you use matches the 10k…

view full answer...

Answer 7

The hitch you referenced, part #41906 is indeed a fit for your 1993 Ford E350. If you look at the photo I have edited for you, you can see the relevant dimensions of the Draw-Tite Class IV hitch, part #41906. I have provided you with the side-to-side…

view full answer...

Answer 8

Hi Arii; the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver #41990-16 is exactly what you need to add a hitch to your 2019 Volvo VNL Semi. This is a weld-on hitch so we recommend taking it to a certified welder for installation.

view full answer...

Answer 9

I do have an option for you but the Curt Trailer Hitch Receiver part #C15800 is designed for passenger vehicles like the Ram 3500, Chevrolet Silverado 3500, and GMC Sierra 3500 so it will not fit your 2009 Volvo D13. However, what you can use is the…

view full answer...

Answer 10

The mounting holes the Curt Trailer Hitch Receiver #14053 measure 38-1/4" and 38-3/4" width-wise and then from the center of the of the forwardmost to the rearmost is 13-1/4". Attached is a dimensional photo for you to reference. This…

view full answer...

Answer 11

I would be happy to help! The Draw-Tite Trailer Hitch Receiver #41906 you were looking at measures 18-1/2" from the center of the rear mounting holes to the center of the hitch pin hole where the Curt Trailer Hitch Receiver #14055 measures…

view full answer...

Answer 12

I attached a picture that shows all of the relevant dimensions of the Draw Tite hitch part #41906 that you referenced for you to check out and see if it would fit.

view full answer...

Dimensions of Weld-On Brackets for Draw-Tite Ultra Frame Trailer Hitch 41990

Featured Help Information

Miscellaneous Media

Continue Researching