Recommended Electric Trailer Jack For 7000lb Pace American Trailer

Question

Question:

Hello I have a Pace American trailer that has a 7000 total weight capacity. The electric jack has failed. Do you have a suitable replacement? Model L812TA2 Thank You

asked by: Darren M

0

Expert Reply:

I have an option that may work for you, but the Model L812TA2 you mentioned did not cross reference with any parts.

I recommend going with the Stromberg Carlson Electric Trailer Jack - Drop Leg - A-Frame - 23" Lift - 4,500 lbs - Black # SC63VR which will install into the a-frame of your trailer and its 4500lb capacity will make raising and lowering the tongue of your trailer quick, and will keep the jack working great for years to come.

I included a video of the # SC63VR for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Hey Brian, completely fair concern - and yes you can, so you won’t be stuck. The etrailer eclectic trailer jacks like 3,500lb #e72QV, 3,500lb with snappad #e22QV, and 5,000lb #e82QV include a manual emergency override. There’s a rubber cap on top of…

view full answer...

Answer 2

In a typical RV-style 7-way the 12V charge circuit is carried on the pin at the 1-o-clock position as you look at the socket from the rear of the vehicle. Please refer to the linked photo. The 12V feed from a vehicle 7-way can deliver just enough…

view full answer...

Answer 3

I recommend using the etrailer.com Electric Jack with a Footplate, part #EJ-3520-BBX, for A-Frames. This trailer jack is rated for 3,500 lbs so it will have more than enough power to lift and lower your tongue weight of 700 lbs. This trailer jack has…

view full answer...

Answer 4

Hey James, yes the Lippert electric jack part #LC285318 would be a great option to replace what you have now. It grounds through it's mounting hardware so you would just need to run a power wire to it's red wire and you'd be set!

view full answer...

Answer 5

Hey Alan! For your 72" slide topper awning, you will need to use an awning like Solera RV Slide-Out Awning - 73" Wide - Black #LCV000165063. This full awning kit is made for slide-outs between 68"-73" wide, so this would be the…

view full answer...

Answer 6

Hello Jeremy, Yes, our etrailer jack #e55ZV will automatically stop and not over raise. If you check out the video that I attached you will see that Steven still has his finger pushing down the button after the jack stops. What kind of application…

view full answer...

Answer 7

I do have several replacement parts available for the RAM Trailer Jack part #TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Rick! The 5,000 lb capacity on the etrailer Electric Trailer Jack #e55ZV you were looking at would be the best option. This will keep it from struggling to lift the rear of your truck and trailer when setting up your weight distribution hitch.…

view full answer...

Recommended Electric Trailer Jack For 7000lb Pace American Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching