Adding Sway Control to 2018 Land Rover Discovery without Weight Distribution Hitch
Updated 03/15/2021 | Published 03/10/2021
Products Featured in This Question
Question:
Good afternoon, TV: 2018 Land Rover Discovery RW:2013 Keystone Premier Ultra Bullet 19FBPRdry weight 4168lbs I am looking to purchase a ball mount with sway tab. I had a couple of questions when looking for the right ball mount. First off the manufactures manual for our vehicle does not recommend WDH since the vehicle has self leveling air suspension. With this in mind we are looking for a ball mount that has a sway tab so we can use with our sway bar. The tongue coupler of our trailer requires a 2 5/16 ball. It is listed as class IV. The ball mount that I found with a sway tab is from Curt and is item 45820. The diameter on the mount for the ball to fit into is 1 inch. I have seen a couple of balls that are 2 5/16 ball and have either 1 inch or 1 ¼ inch diameter. They are listed as class III. My first question is can I use the class three setup which is the mountCurt 45820 and a 2 5/16 ball, 1 inch diameter, both rated at 7500lbs with the trailer class IV coupler? If this works out then my next question would be do you have a 2 5/16 ball, 1 inch diameter that will work with this mount? Also, in the description the Curt 45820 it says it has a two inch . According to the manufacture of our vehicle the top of the tow ball should align with pin, would these measurements work with your products?
asked by: Jason O
Expert Reply:
You are correct in looking at the Curt Ball Mount w/ Sway Control Tab for 2" Hitches # D320. The hitch rating on the trailer is a class IV rating as a maximum. The ball mount you see is still within the maximum weight of your Keystone Premier Ultra Bullet so you will be fine. This also will give you the closest possible fit for your tow ball height requirement by Land Rover. For the ball use 2-5/16" Hitch Ball - 1" Diameter # C40007. It has the 1" diameter shank that you need for the ball mount.
Here is the Friction Sway Control Kit # 83660. It includes the ball for the ball mount, the camper ball mount and of course the sway bar itself. As an added reminder I recommend to only use the sway bar on long straight highways. They have a tendency to break or bend when backing up as you are doing a lot of steering changes so always remove before backing up or when you are on extremely tight roads.
Product Page this Question was Asked From
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: tekonsha 90195
- Search Results: tekonsha p3 brake controller
- Search Results: etb7 kit
- Search Results: city water inlet
- Search Results: tekonsha 90195 p3
- Shop: Trailer Wiring
- Shop: Vehicle Tow Bar Brake System
- Shop: Brake Controller
- Q&A: When to Use a 20 or 30 amp Circuit Breaker When Installing Brake Controller
- Shop: Curt Discovery NEXT Trailer Brake Controller w/ Plug-In Harness - Up to 4 Axles - Time Delayed
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Plug-In Harness - 1 to 4 Axles - Proportional
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires
- Video: Feature Review Tuson DirecLink Base Model Trailer Brake Controller
- Video: Curt Wiring C57202 Review
- Video: Feature Review Curt Universal Wiring Kit for Trailer Brake Controllers
- Video: Detailed Breakdown of the Curt Trailer Connector Adapter with Backup Alarm
- Video: How to Choose a Trailer Brake Controller
- Shop: Victron MultiPlus-II Inverter Charger with 1 AC Input - 2,400 Watts - 50 Amps - 12V - UL Listed
- Shop: Wire Loom Clamp - 1/2" Diameter Opening- Metal with PVC Sleeve - Qty 100
- Shop: WFCO Auto Detect RV Converter and AC/DC Distribution Panel - 12V - 40 Amp
- Q&A: Parts Needed to Add Gas Strut to RV Entry Door
- Q&A: Why is a Weight Distribution System Not Recommended on a 2018 Land Rover Discovery
- Q&A: Can Weight Distribution Be Used On a 2003 Land Rover Discovery II with Curt Hitch
- Video: A Closer Look at the Redarc Encapsulated Power Diode for Tow-Pro Brake Controllers
- Video: Let’s Check Out the Curt Universal Installation Kit for Trailer Brake Controller
- Q&A: Troubleshooting Compatibility Issues With A Tekonsha P3 In A 2024 Honda Ridgeline
- Q&A: Looking For Budget Friendly Weigh Distribution Hitch To Pull 5K Dump Trailer
- Article: How to Measure for Trailer Hitch Drop
- Q&A: What Is The Span Or Usable Length Of RV Designer Hitch Pin - 1/2" # RD83GR
on Trailer Hitch Ball Mount
