Customers compare RED34FR to these similar products
Products Featured in this Video
Jeff: Hello everybody, this is Jeff at etrailer.com. Today, we're going to take a look at the REDARC Encapsulated Power Diode for the Tow-Pro Brake Controllers. Now this diode will prevent feedback to ensure correct operation of your REDARC Tow-Pro trailer brake controller and your vehicles brake lights. The diodes designed to fit in the trailer… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
We currently do not have any installation videos for the Redarc Encapsulated Power Diode #RED34FR being used to install the Redarc Tow-Pro Liberty Brake Controller #RED24FR with the Harness #RED69FR and Panel #RED48FR for any vehicles or your 2021…
view full answer...The best place to find the stoplight circuit on a vehicle like your 2020 Subaru Outback is going to be at the brake pedal switch. You'll need to use a circuit tester like part #PTW2993 to test all of the wires till you find the circuit that…
view full answer...There sure is! The Redarc Encapsulated Power Diode for Tow-Pro Brake Controllers #RED34FR you were looking at gets wired as shown in the included diagram. One of the red wires goes to the red brake output wire on your trailer brake controller, the…
view full answer...I recommend the Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional Item #C51180. If the dealership is installing the 7 pole connector, this controller doesn't require any additional wires to be ran inside the vehicle. Your…
view full answer...I would be happy to help! You are correct that on vehicles like your 2016 Kia Sorento you will not want to get the brake light signal directly from the stop light switch. Picking up the signal there will only activate the trailer brakes when you…
view full answer...I would not recommend installing a Diode #RM-690 on the brake line as this is a part which can fail and if it were to you could risk doing a lot of damage. While the Bright Way Push-to-Test ICU Trailer Breakaway Kit #BW94FR could risk damage to your…
view full answer...Before you can install a trailer brake controller in your 2022 Toyota Highlander you'll first need to make sure that you have a 4-pole wire harness for your lights installed and then a 7-way wire harness to get your brake function. If you…
view full answer...Yes. You can use your existing weight distribution hitch with the Gen-Y Torsion 2 Ball Mount #325-GH-1324 without any additional components, but it is not the optimal setup. Gen-Y recommends that you use the Gen-Y Torsion Weight Distribution Shank -…
view full answer...A weight distribution system does not increase a hitch's tongue weight capacity. Rather, it takes weight off of the tongue, helping loads stay stable and level. In other words, if you use a trailer without a weight distribution system with a…
view full answer...I recommend installing the Redarc Tow-Pro Liberty Brake Controller #RED24FR on your 2019 Jeep Wrangler. This will connect to your factory wiring of the tow package with the Plug-and-Play Wiring Harness #RED93RR. The Universal Mounting Panel…
view full answer...Thanks for the pictures you sent! It looks like you don't have the right plug under your dash which is due to not having the factory tow package on your 2020 Ford Ranger. That's ok, since there's still a solution to adding brake…
view full answer...For your application I actually recommend using the Roadmaster Universal Stop Light Switch Kit #RM-751000 to send a brake signal to the brake controller. I looked up the online version of the owner's manual for your 2022 Toyota Highlander but it…
view full answer...