How Much Gap Should There be Between Frame and Timbren Suspension Kit

Question

Question:

You previously answered a question regarding distance between Timbren and Axle. Here is an answer from Timbren, Ideally “no gap” is best unloaded.

asked by: Adam

0

Expert Reply:

I found the article you mentioned from Timbren and a 1 inch gap is recommended for the rear kits but for the front kits they recommend no gap at all. Since the part # TGMFK25D is a front kit you'd want to not have any gap at all.

expert reply by: Jameson C

0

Answer 1

The Timbren rear jounce spring kit #TTORTUN4L is the correct one for the 2012 Toyota Tacoma 4X4 non-Pre-Runner that has the OEM 3-leaf rear spring suspension. The bottom leaf of these springs can be seen in the linked photo that shows a…

view full answer...

Answer 2

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to…

view full answer...

Answer 3

There are a few different options that we have for you to install a Timbren Rear Suspension Enhancement System on your 2010 Toyota Tacoma that is 4WD. Please keep in mind that any suspension enhancement system will not increase your weight capacity.…

view full answer...

Answer 4

The ideal gap between the bottom of the jounce bumper and top of the contact point is about 1/2"-1" but you can go more if you don't want them to engage as soon or as often. Therefore, in lifted applications you'll need to use…

view full answer...

Answer 5

I will be happy to provide some dimensions for you for the Timbren rear suspension enhancement system, #TDR1500DQ, for your 2012 Ram 1500. First, the height of the spring by itself is 5-1/2 inches. The springs have a diameter of 4 inches. I have…

view full answer...

Answer 6

Hey Josh. The Timbren Rear Suspension Enhancement System item #TTORTUN4L has an overall height of 4.6" including the bracket. Timbren recommends a 1" gap between the spring and where the old bump stop hits. The Timbren item #TTORTUN4L is…

view full answer...

Answer 7

Yes, you can use a Timbren system like the part #TGMRCK15S with a weight distribution hitch on a 2017 Chevy Silverado 1500. If you have the WD system already you'll have to go through the setup process again after the Timbren install since…

view full answer...

Answer 8

For a weight distribution system, there are always exceptions,but in general the systems with only bars and chains do not have sway control. They are adjustable in tension for different weight, but are a little more work. The bar systems whether…

view full answer...

Answer 9

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How Much Gap Should There be Between Frame and Timbren Suspension Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching