Draw-Tite Trailer Hitch And Wiring Harness For 2019 Nissan Pathfinder

Question

Question:

I have a 2019 Nissan Pathfinder and am buying the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2 I will be pulling a boat and need trailer wiring for lights, etc. What do I need for that? The video wasnt specific. Thanks!

asked by: Tom F

0

Expert Reply:

We can get your 2019 Nissan Pathfinder set up with a trailer wiring harness to go along with the Draw-Tite Max-Frame Trailer Hitch Receiver # 76031. The best option is the harness from Tekonsha because they make the most reliable trailer wiring harnesses, and because it has the highest amp rating, which means it gives you the best prevention against potential shorts. The harness that fits your 2019 Pathfinder is the following:

- T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118670

Then, in order to mount it, I recommend the No-Drill Mount for Electrical Mounting Bracket # 18140 with Mounting Bracket 4-Pole Flat # 18144.

Additionally, since you are using it on a boat trailer, I highly recommend Dielectric Grease in order to help prevent against corrosion; what you will need is the Dielectric Grease for Electrical Connectors # 11755.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Draw-Tite Trailer Hitch And Wiring Harness For 2019 Nissan Pathfinder

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching