Will Draw-Tite Trailer Hitch Receiver 41935 Fit My 2008 Toyota Tundra With Aftermarket Rear Bumper?
Question:
My factory installed hitch was worn out and the bumper was beat up pretty bad. I removed both the bumper and hitch and only replaced the bumper with an aftermarket bumper and brackets. Can i now use the drawtite hitch 41935 on my truck?
asked by: Joe S
Helpful Expert Reply:
The Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2" # 41935 is an excellent choice and is confirmed to fit your 2008 Toyota Tundra. You likely will not have an issue, but it really depends on if your aftermarket rear bumper hangs lower than the factory bumper.
To determine exact fitment in your situation, you will want to measure from the ground to the bottom of your bumper. This hitch measures 18-1/4" from ground to top of hitch receiver when the truck is equipped with factory suspension height. If your measurement from the ground to the bottom of the bumper is more than 18-1/4" then you will not have an issue. If you have a lift kit or different suspension then you will need to take that into consideration when comparing measurements. I have attached an installation video for this trailer hitch receiver.
Product Page this Question was Asked From
Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1200 lbs TW
- 12000 lbs GTW
- 14000 lbs WD GTW
- 2 Inch Hitch
- 1400 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Video: Mount: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Video: DIY Install: Draw-Tite Ultra Frame Trailer Hitch Receiver on your 2010 Toyota Tundra
- Shop: Trailer Wiring
- Q&A: Hitch to Use TorkLift Tie Downs on a 2007 Toyota Tundra 8 Foot Bed
- Q&A: Comparing Draw-Tite and Curt Trailer Hitches for the 2013 Toyota Tundra
- Q&A: Does the Curt Hitch C15398 Support the Bumper on a 2013 Toyota Tundra?
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Article: Transmission Cooler
- Article: Frequently Asked Questions About Transmission Coolers
- Article: How to Measure for Trailer Hitch Drop
- Shop: Towing Mirrors
- Shop: Transmission Cooler
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: Finding the Right Trailer Wiring Harness
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: hitch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Shop: Brake Controller
on Trailer Hitch
