Recommended Weight Distribution System with Sway Control for 7" Tall Trailer Frame

Question

Question:

Can you recommend a weight distribution hitch with sway control in the 10,000 pound area? It is for an aluminum frame enclosed trailer with a 2x7 tongue. Want a no drill style that is clamp on though some Im seeing say the max tongue size is 6.

asked by: Jason J

0

Expert Reply:

The Curt TruTrack Weight Distribution System part # C17500 is my recommendation for an integrated weight distribution system with sway control. It also has a pre-torqued hitch ball as well so setup will be very simple. It can be used on trailer frames up to 8" tall with the Frame Brackets for Curt TruTrack Weight Distribution System part # C17515.

expert reply by: Conner L

0

Answer 1

Welcome back Don! The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET is exactly what I would recommend using. This is a solid reliable system and the built in sway control will make a noticeable improvement in ride…

view full answer...

Answer 2

-Hey Tom, Equal-i-zer makes frame brackets for 8 inch trailer frames. For that you would need the part #EQ90-02-5378 for outer link and then for an inner link part #EQ90-02-5208. You'd need two of these with the system you order since the…

view full answer...

Answer 3

Weight distribution systems that have 2-point sway control generally have sway control just at the ends of the springs bars on the trailer side. On the Fastway systems for example the L bracket that secures the bar to the frame bracket can be…

view full answer...

Answer 4

Hi Garrett! We do have options for your 2015 Kenworth T270, but there are not going to be any custom fit hitches available. If I were doing this, I would go with the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44"…

view full answer...

Answer 5

Hi John, Reese went out of business earlier this year, so any Reese products we carry are the last of our stock and we no longer have the Reese 66093. I did some research and it looks like the GVWR of a 2025 or 2026 Rockwood Mini Lite 2515S is…

view full answer...

Answer 6

Hey Tim, thanks for reaching out! The .75" sag you're seeing is acceptable, that will not have much of an effect on drive quality at all. If you'd like to totally level out your ride, then add the Air Lift LoadLifter 5000 Ultimate Air…

view full answer...

Answer 7

There's a couple key differences between the Equal-I-Zer Weight Distribution systems #EQ37121ET and #EQ37100ET that you referenced. The biggest being that the tongue weight range is different. The part #EQ37100ET has a range of 600-1,000 lbs and…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Recommended Weight Distribution System with Sway Control for 7" Tall Trailer Frame

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching