Off-Road Axle Setup for Intech Chase Flyer

Question

Question:

Hello, Im looking at the Timbren Heavy-Duty Axle-Less Trailer Suspension - 4 Lift Spindle - Off-Road Tires - 3,500 lbs Item # ASR35HDS02. My first question is if they have been installed on a Intech Chase Flyer, if its applicable. Second, Is it safe to attach to the aluminum frame. Third, I have trailer brakes on my current system, can I reuse on the Timbren. Finally, could you quote me everything needed to make the change. Id like to update the tires and wheels to a more all terrain tire as well. Thanks

asked by: Brian K

0

Expert Reply:

I did some checking online and found that Intech actually offers an off-road package for the Chase Flyer that uses the Timbren Axle Less kit, so while we haven't had the chance to do it we know it is possible. We also know these can be used on aluminum trailer frames as well.

Since this kit uses a higher capacity spindle since it was designed with off-road use in mind it actually uses 5,200 lb axle hubs like the part # 8-201-9UC3-EZ and then the brake assemblies needed would be the kit part # AKEBRK-7-SA and you'd be set.

Then for an off-road wheel and tire that will bolt up to the hub mentioned we have the # LH66FR which has an off-road tire like you are wanting.

expert reply by: Jameson C

0

Answer 1

Hey Jose, do you know how wide the channel is on your trailer tongue? I would go with the Lock N Roll Articulating setup but the correct trailer side coupler will be based on the width of your tongue. I looked up pictures of your 2023 Intech Flyer…

view full answer...

Answer 2

This is a great question. I called my contact at Progress Manufacturing (creator of Equalizer and FastWay Weight Distribution products) to pick his brain on this topic. He explained that weight distribution (WD) and sway control products rely on…

view full answer...

Answer 3

That area where the fan is and buzzing sound you referenced is your power converter. That is what converts the 120v AC shore power into the 12v DC power for your lights, fans, etc., and charges/maintains your battery. To replace that converter with a…

view full answer...

Answer 4

The breakaway setup should still activate the brakes to the point you can hear the magnets hum. The fact you can't hear yours means your setup isn't working currently. It's possible you have a dead breakaway battery or the wiring has…

view full answer...

Answer 5

Sounds like there's a short on one of the trailer wiring circuits. Without knowing more specifics on your vehicle and the trailer wiring setup you have the best option would be to check the wiring of the trailer by going over it looking for any…

view full answer...

Answer 6

Sometimes you can hear a slight buzzing sound when you hook up your 7-Way but not always. This may be the case in your situation. Typically when people hear the buzzing noise is when the brakes are engaged. If you are not applying the brake pedal in…

view full answer...

Answer 7

Thanks for sending the photo of your axle tag, that made everything super-easy. The spindles on your Dexter #11 5K axle use an LM67048 outer/25580 inner wheel bearing and a 10-36 grease seal. We offer the inner/ outer bearings and races as well as a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Off-Road Axle Setup for Intech Chase Flyer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching