Replacement Lid Support for a Yakima SkyBox 16

Question

Question:

Hello - Im looking for replacement hinges for Yakima Skybox 16. Im not seeming to find them on your site. They are pictured in the description of the Skybox 16 attaching to the top and bottom parts. Can you point me in the right direction for these?

asked by: Adam

0

Expert Reply:

It sounds like you are needing the lid supports for your Yakima SkyBox 16, part # Y07335. We have that here. It's part # 8880683.

These may look a bit different than what you are used to, but that is because Yakima has updated their supports. This is confirmed to work with your SkyBox.

expert reply by: Kef G

0

Answer 1

To install the Lid Support #8880683 on your RocketBox 11 you simply need to determine if your current support is connected with a ball joint or with a screw. If it's a ball joint then you'll use a mallet to uninstall the old support and…

view full answer...

Answer 2

For starters, there are a few different generations of the Yakima SkyBox 16 and I would need to know which one you have in order to recommend the correct replacement hinges. I called Yakima and they were not able to reference the part number you…

view full answer...

Answer 3

Yes, the Replacement SuperLatch Handle Assemblies part #Y8880348 will be a direct replacement for your Yakima SkyBox 16s Rooftop Cargo Box 8007178. It is the exact same assembly that you have attached a photo of. I have attached a list of other…

view full answer...

Answer 4

The Replacement Front Lid Support for Yakima SkyBox 12 and SkyBox 16 Rooftop Cargo Boxes 2009 and Newer #8870090 is universal for the front and rear. I've attached a couple photos of the installation instructions to assist.

view full answer...

Answer 5

I checked with Yakima and for your Skybox 16 the correct lid support for the rear is supposed to be part #8870072 and for the front is part #8870090. The picture you submitted shows a broken or twisted part #8870090 so that is what you'd need as…

view full answer...

Answer 6

The Replacement Rear Lid Support for Yakima SkyBox 12 and SkyBox 16 Rooftop Cargo Boxes 2009 and Newer 8870088 was originally attached with the rivets you have attached a picture of. The new support comes with screws that are used instead. You can…

view full answer...

Answer 7

I did some research and it looks like your 2022 Toyota Sienna has adjustable aero crossbars. The Yakima SkyBox NX 16 Roof Cargo Box item #Y95AV. is compatible with aero cross bars and fits a crossbar spread of 24" - 36". This means how far…

view full answer...

Answer 8

Yakima recommends the use of a rubber mallet to get the ball into the socket of the #8880683. Since plastic is a bit more flexible when warm you might take a heat gun or blow dryer to warm everything up and allow it to fit easier.

view full answer...

Answer 9

The Yakima Skybox 21 part #Y07337 made from 2014 to present has a much more aerodynamic shaped lid than the Yakima Skybox 21 part Y07184 made from 2009 to 2014 had. I have attached a photo of each so you can see the difference. If you have the 09-14…

view full answer...

Answer 10

Is this the latch you are looking for? 8870090 Replacement parts for your box aren't all available but I believe this might be what you are looking for.

view full answer...

Answer 11

Thanks for the picture of your Yakima box's lid support. Based on that I can tell you that the part #8880683 is the correct replacement you are looking for.

view full answer...

Answer 12

For your Yakima SkyBox, you are going to need the Replacement Mounting Clamp for Yakima SkyBox Cargo Boxes #Y62XR. This replacement clamp will work on all Yakima SkyBoxes, so if that's what you have this'll work fine. If this is not what you…

view full answer...

Replacement Lid Support for a Yakima SkyBox 16

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching